Mitel Voice Processing Solutions Installation And Service Manual

CP 6572
Page 4 of 4VoiceMemo Release 6.OA and later
SteD24. The server takes approximately 45 minutes complete the process. The server
displays the following message when the replace disk is done:
PlWY2pt:***************X**X********Xk***XX*X*XX*~~~~~~~~~~
* Set hard disk parameters by selecting option S *
* from the HARD DISK UTILITIES MENU after system ** reboot.*
* Please shutdown system and adjust disk 1:l*
* to disk 1:2, then reboot. If needed, update *
* redundancy by updating disk 1:2 from its...

cl? 7004Name the Configurations
Page 1 of 1
VoiceMemo Release 6.OA and later
This procedures describes how to name the two system configurations. Use descriptive
names to help you remember the differences between the two configurations.
Step
1.Reach the VoiceMemo Configuration Main Menu, then go to the VoiceMemoActive Configuration Menu.
2. Name the configuration.
Select:(N) Name Configurations
prompt: Enter the configuration number to name (CR for
no change) :Response: Number (0 or 1) of the...

cl? 7005View the Configuration Names
Page 1 of 1
VoiceMemo Release 6.OA and later
This procedures describes how to view the names of the two system configurations.
Step
1.Reach the VoiceMemo Configuration Main Menu, then go to the VoiceMemoActive Configuration Menu.
2. View the report.
Select:(V) View Configurations
Pr~mpti Configuration last modified by OFFLINE
CONFIGURATION is n.
Where 
FZ is the number of the configuration.
The system displays the report and returns to the command line.
Reference
Menu...

Enable a Modulecl? 7014
Page 1 of 1
VoiceMemo Release 6.OA and later
This procedure describes how to enable a module to return it to normal call processing
operation. When changing the status of multiple modules, always change the one the
console is attached to last.
FOR THE MODEL 120 AND MODEL 70 ONLY: Some system prompts in this
procedure may contain generic references to other multiple-module Centigram Series 6
products. In such cases, shaded areas indicate a difference in operations for the Model
120...

CP7015Update Disk 
RedundFcyPage 1 of 1VoiceMemo Release 6.OA and later
This procedure describes how to update the disk redundancy. Each hard disk is
partitioned into multiple logical drives.To make sure all drive partitions are updated,
use the “Update all out of synchronization hard disks” option.
Note:
The server allows you to watch the number of the sector number being updated,but this display slows the verification process.
Usethefollowing table to determine which types of drives should be updated....

Shut Down a Hard DiskCP7017Page 1 of 1
VoiceMemo Release 6.OA and later
This procedure describes how to shut down a hard disk, removing it from service. This
process requires the server to contain redundant disks.
SteD
1.Reach the Hard Disk Utilities Menu, then go to the SCSI Status Menu.
2.Shut down the disk.
Select:(S) Shutdown SCSI BUS or disk
Prompt: SCSI Shutdown Menu
Select:(D) Shutdown a SCSI disk
Prompt:Input a disk in the following range:*.nn nn nn
Which Disk?
Response: Enter the two-digit SCSI...

Enable a Hard Diskcl?7019Page 1 of 1
VoiceMemo Release 6.OA and later
Th
e procedure describes how to enable a disk. This process requires the server to
contain redundant disks.The Update Redundancy procedure described in CP 70 15 must be run before the disk is
available for the server to use.
FOR THE MODEL 120 AND MODEL 70 ONLY: Some system prompts in this
procedure may contain generic references to other multiple-module Centigram Series 6
products. In such cases, shaded areas indicate a difference in...

CP 7022
Add or Cancel a Phoneline ExceptionPage 1 of 2
VoiceMemo Relase 6.OA and later
This procedure contains instructions for setting any phoneline exception. Phoneline
exception changes take effect on the next new call after saving the settings. A table for
converting port numbers to line numbers follows the procedure.
StepReference
GD Add a Phoneline Exception
1.Reach the Phoneline Exceptions Menu.
2.Select line to change.
Select:(A) Add exception
*.
Prompt: Keep entering triplets, then enter  on a...

Cl? 7022
Page 2 of 2VoiceMemo Relase G.OA and later
Step
3.Select the phoneline exception to reset.
Prompt:command to cancel =
Response: The number of the phoneline exception to reset
4.Repeat steps 8 and 9 for each phoneline exception you want to change. When you
are finished, press Enter.
5.Enter the next line to be changed, or press Enter to exit.
3
Dot. RN. A
Refirence 

CP 7025
Activate New 
SobarePage 1 of 1VoiceMemo Release 6.OA and later
This procedure describes how to activate new software loaded via the Online 
SobareUpdate program.
ja\WARNING!This procedure resets the server,causing loss of call processing
capabilities. Centigram recommends that this process be completed
during periods of low call traffic.
Step
1.Reach the System Maintenance Menu, go to the System Maintenance Additional
Options Menu, then select S to go to the Online Software Update Menu.
2....