Mitel SX-200 DIGITAL Pabx Information Manual

Shipping, Receiving, And installation Information 
CHART 5-8 (CONT’D) 
INSTALL BAY 3 KIT INTO AN SX-200@ UNIVERSAL CABINET 
Step 
I Action Comments 
13. 
14. 
15. 
16. 
17. 
18. 
19. 
20. Connect the DC power cable leads to the 
Bay 3 backplane, as shown in Figure 4-7. 
Connect the DC power cable to the 
interconnect card as follows: 
TB301-1 brown 
TB30 l-2 blue 
TB301-3 braided gnd cable to Control shelf 
frame 
TB301-4 nc 
TB301-5 nc 
TB30 1-6 orange 
TB30 1-7 yellow 
Connect leads from switch and LED...

Shipping, Receiving, And Installation Information 
CHART 5-8 (CONT’D) 
INSTALL BAY 3 KIT INTO AN SX-200@ UNIVERSAL CABINET 
Step 
21. 
22. 
23. 
Action Comments 
Replace power panel onto cabinet. 
Unpack rear door power supply assembly (pn If damaged or wrong type, repack in 
102966503); inspect for physical damage, and original container and return with 
correct type. completed Damage Report. 
Place rear door power supply onto lower 
door support, using shim washer, and lock 
door into closed position...

Shipping, Receiving, And Installation information 
Step 
33. 
34. 
35. CHART 5-8 (CONT’D) 
INSTALL BAY 3 KIT INTO AN SX-200@ UNIVERSAL CABINET 
Action 
Unpack each printed circuit card and insert it 
into its assigned slot. Comments 
Connect PCM cable previously routed 
between the shelves to connector J2 on the 
front of the Digital Interface Card at Bay 3, 
slot 18. 
Power up DPABX and reprogram using 
Customer Data Entry. 
Page 5-17  

Shipping, Receiving, And Installation Information 
GREEN , 
K~0014ROE0 
Figure 5-3 Grounding - Bay 3 to Frame 
TB301-3 
I 
TBl 
INTERCONNECT 
CARD 
I 
KA0015ROEO 
Figure 5-4 Grounding - Bay 3 to Interconnect Card 
Page 5-18  

Shipping, Receiving, And Installation information 
IPPER SUPPORT 
SHIM WASHERS 
REAR DOOR 
POWER SUPPLY 
FAN ASSEMBLV 
KAOOlGRlEl 
Figure 5-5 Grounding - Fan Door to Frame 
Page 5-19  

Shipping, Receiving, And installation Information 
CHART 5-9 
INSTALL DIGITAL PERIPHERAL SHELF 
Step Action Comments 
INSTALL BAY 3 KIT 
1 
Unpack and inspect contents of kit. 
2 
Power down system. 
3 Open front door and slide digital peripheral 
shelf onto top of Control shelf, 
and fasten to 
front rails with eight lo-32 x 0.5 in. screws, 
as shown in Figure 5-6. 
4 Install filler plate above shelf, and fasten to 
front rails with two IO-32 x 0.5 in. screws, as 
shown in Figure 5-6. 
5 Open rear door,...

Shipping, Receiving, And Installation information 
CHART 5-9 (CONT’D) 
INSTALL DIGITAL PERIPHERAL SHELF 
Step Action 
Comments 
INSTALL BAY 4 KIT 
1 Unpack and inspect Bay 4 kit. 
2 Power down system, and open rear door. 
3 Attach backplane to cardfile with six screws, 
flat washers, and lock washers (as Bay 3); 
place double tab connector at lower left 
corner instead of flat washer. 
4 Connect two ground wires to Bay 3 and to 
Bay 2, as shown in Figure 5-7, using hex 
nuts and split lock washers. Refer...

Shipping, Receiving, And Installation Information 
i-l - 
‘ 
/ 
PANEL 
/ SCREWS (2) 
CARD FILE SCREWS (8) 
KA0239ROEO 
Figure 5-6 Install Digital Peripheral Bay and Panel 
Page 5-22  

Shipping, Receiving, And Installation Information 
CARD FIL 
TO CABINE 
FRAME 
7 
AC LINE 
CORD- 
E6- 
E4 
DG- 
E31 
EDG 
J17A/ 
J17B’ 
A---- 
--- 
_---. 
-- 
-- 
--- 
/ J17A 
,J17A 
PCM CABLES 
y WITH GROUNDS 
TO FASTON TABS 
-E5 
-E5 
Q 
a 
(I AC CORDS 
m GROUND WIRES 
_ BRAIDED GROUNDING SHIELD 
KA023BROEl 
Figure 5-7 Digital Peripheral Bay Connections 
Page 5-23  

Shipping, Receiving, And Installation Information 
KA0107ROEO 
Figure 5-8 Digital Peripheral Bay Ground Connection Details 
Page 5-24