Mitel SX-200 DIGITAL Pabx Information Manual

Shipping, Receiving, And Installation Information 
MUSIC ON 
HOLD/PAGER 
MODULE RECEIVER/RELAY 
MODULE --j---t 
CONSOLE 
MODULE E&M TRUNK 
LED’s 
UNIVERSAL CARD i. -SWITCH 
J 
J MODULE 1 
J MODULE 2 
I MODULE 3 
04--- MODULE 4 
T ALARM 
I 
4 z 
KAOOPlROEO 
Figure 5-18 Universal Card and Modules 
Page 5-45  

Shipping, Receiving, And Installation information 
7666R2 
Figure 5-19 Installation of Module onto Universal Card 
Page 5-46  

Shipping, Receiving, And installation information 
CROSS-CONNECTION 
MODULE FIELD 
T/R PAIR 
Tl 
Rl 
T2 
R2 
T3 
R3 NO CONNECTION6 
CONSOLE MODULE 
-- _---- -----_ 
1 
I 
ofy”;s -“cl poA 
40 OHMSI POB 
pm+< CONTAIX RATING / Fz 
3OO%i%lS , 
---------____ 
MUSIC ON HOLD/PAGING MODULE 
300 OHMS 
--Gig- K5A 
K5B 
SUBCIRCUIT 5 
300 OHMS 
GqJ(- K6A 
K6B 
SUBCIRCUIT 6 
RELAV MODULE 
- 
t 
t 
-.- 
-.- 
-e 
t 
-.- 
t 
4 
- 
J 
- 
NOTE 1. All wiring must be done in accordance with the National 
Electrical Code...

Shipping, Receiving, And Installation Information 
CHART 5-20 
INSTALL FLOPPY DISK DRIVE 
Note: Remove diskette from drive while power is on and LED is off. Remove power from the Bay 
before removing or installing a disk drive. 
Stern Action Comments 
INSTALLATION INSTRUCTIONS FOR PLOPPY DISK DRIVE pn 9109-024-000 
1. 
2. 
3. 
4. 
5. 
6. 
L 
1. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
Page 5-48 While wearing the antistatic wrist strap, 
unpack and inspect the floppy disk drive. 
Insert the floppy disk drive into its...

Shipping, Receiving, And Installation Information 
SlGkiAL 
CAl3LE , POWER 
/ CABLE 
PN9109-024-000 
RIBBON 
CABLE Loop 
HEIGHT MUST BE LESS 
THAN CASE HEIGHT FOR 
INSERTING DISK DRIVE 
INTO SHELF 1’ 
i 
FLdPPV  
‘L. 
‘ 
FRONT COVER 
DISK DRIVE LOCKING SCREW 
(ENCASED) 
7699ROE 
CONNECTOR 
PN9109-124-000 1 
 LOCKING 
SCREW 
8536ROEl 
/ LATCH 
Figure 5-21 Floppy Disk Drives 
Page 5-49  

Shipping, Receiving, And Installation Information 
CABLE 
CABLE 
KA0186ROEO 
Figure 5-22 Disk Drive Connections 
Page 5-50  

Shipping, Receiving, And Installation Information 
CHART 5-21 
UNPACK AND INSTALL PRINTED CIRCUIT CARDS 
Step Action 
Comments 
CAUTION: DO NOT OPEN OR UNPACK ANY 
THE ANTISTATIC WRIST STRAP 
PRINTED CIRCUIT CARD CARTONS UNLESS 
MUST BE CONNECTED TO THE PABX 
YOU ARE WEARING THE ANTISTATIC WRIST 
CHASSIS, WHICH MUST BE 
STRAP. 
CONNECTED TO AN APPROVED 
GROUND TO PROVIDE PROTECTION 
FROM STATIC DISCHARGES. 
1. 
2. Attach the antistatic wrist strap to your 
The system configuration and/or the 
wrist, and...

Shipping, Receiving, And installation Information 
Step 
9. 
10. 
11. 
CHART 5-21 (CONT’D) 
UNPACK AND INSTALL PRINTED CIRCUIT CARDS 
Action 
Unpack trunk cards (for Control and 
Peripheral bays), set switches or jumpers 
(refer to Charts 5-22 through 5-26) and 
install into assigned slots. 
Comments 
Unpack, inspect, and install the remaining 
PCB cards according to Figures 2-l or 2-2 
and the equipment assignment for this 
system. 
Retain some packing material for returning 
cards for repair. Discard...

Shipping, Receiving, And Installation information 
SHIPPING CARTON 
HOLDING 10 OR 5 
INDIVIDIJALLV PACKAGED 
CIRCUIT CARDS 
7105ROEC 
Figure 5-23 Printed Circuit Card Packaging 
Page 5-53  

E 
E 
I 
I 
I 
I 
-0, 
f 
I 
, -, I-----I 1 66000 PROCESSOR 1 
. 
t 
SYSTEM 
RESET 
El 
RESET 
ALARM 
0 
PLANE 
TRANSFER 
El 
0 
0 
0 
0 
NOTE: 
ACTIVE 
MINOR 
MAJOR 
CRITICAL