Mitel SX-200 DIGITAL Pabx Information Manual

Shipping, Receiving, And Installation Information 
7. UPGRADING AN EXISTING SX-200@ PABX TO AN SX-200@ DIGITAL 
PABX 
Strategy 
7.01 
The control cabinet will be installed beside the existing 
SX-200@ DIGITAL PABX cabinet, equipped with the new atten- 
dant console, new stations, trunks, or features for Bays, 1, 2 or 3, and 
powered up. All testing can be completed and the new database 
entered with CDE, including all equipment in the existing SX-200@ 
system. The existing SX-200@ DIGITAL PABX is then...

Shipping, Receiving, And Installation Information 
CHART 7-l 
SX-200@ PABX UPGRADE TO SX-200@ DIGITAL PABX 
Step 
1. 
Action 
Unpack the Control cabinet and place it in its 
assigned location following the installation 
charts in Part 5 of this Section. 
Comments 
2. Relocate the #6 AWG system ground to the NOTE: Connect a temporary jumper 
common ground stud in the control cabinet. 
between the SX-200@ cabinet and 
Concurrently install the PCM cable between 
the ground wire so that an electrical 
the...

Shipping, Receiving, And Installation Information 
CHART 7-l (CONT’D) 
SX-200’ PABX UPGRADE TO SX-200@ DIGITAL PABX 
Step 
11. 
Action 
Remove all existing consoles from the 
system and repack them. 
Comments 
12. If peripheral shelf card assignments are to be 
changed, reposition the cards at this time. 
13. Continue with the installation by following To minimize wiring changes, it is 
the charts for installing a peripheral cabinet recommended that existing station 
(Bays 4 and 5). and trunk assignments...

Shipping, Receiving, And Installation Information 
APPENDIX A 
FCC INTERCONNECTION REQUIREMENTS 
TELEPHONE COMPANY INTERCONNECTION 
General 
Al.01 
This equipment has been approved by the Federal Communica- 
tions Commission (FCC) as not being harmful to the telephone 
network when connected directly to the telephone lines through the 
standard 50-pin blue ribbon prescribed by the FCC Rule. This Section 
is applicable to telephone interconnection in the United States. 
Notification 
Al.02 
Prior to the...

Shipping, Receiving, And Installation Information 
performing any maintenance operations other than those specifically 
included in this Standard Practice. 
Al.06 Circuit cards may be removed by the user; however, replace- 
ment cards are to be supplied only by MITEL or its authorized 
agent. No field repair of circuit cards by the user is authorized. 
Al.07 No cabling or wiring changes within the console are permitted 
by the user. Plug-ended cables, as detailed in this Standard 
Practice, are to be...

Shipping, Receiving, And Installation Information 
TABLE Al-l 
USOC CONNECTOR PIN DESIGNATIONS 
35 R-S T E T 
10 S-R R M R 
36 BK-BL T T 
Tl 
11 BL-BK R R Rl 
37 BK-0 T E E 
12 0-BK R M M 
Pair Connector Type 
Pin 
Colour RJ21 X RJ2EX RJSGX 
38 
BK-G T T T 
13 G-BK R 
R R 
39 BK-BR T 
E Tl 
14 BR-BK R 
M RI 
40 BK-S T 
T E 
15 S-BK R 
R M 
41 Y-BL T 
E T 
16 BL-Y R M R 
42 Y-O T T Tl 
17 O-Y R R RI 
43 Y-G T E E 
18 G-Y R M M 
44 Y-BR T T T 
19 BR-Y R 
R R 
45 Y-S T E Tl 
20 S-Y R M Rl 
46 V-BL T- 
T E...

MITEL STANDARD PRACTICE SECTION MITL9108-093-206-NA 
Issue 2, September 1986 
SX-200” DIGITAL 
PRDVATE AUTOMATIC BRANCH EXCHANGE (PABX) 
INSTALLATION FORMS 
Copyright of MITEL Corporation 1986 
TM - Trademark of MITEL Corporation 
@Registered Trademark of MITEL Corporation  

installation Forms 
CONTENTS 
PAGE 
1. INTRODUCTION ................................... I-l 
General ......................................... I-I 
Reason for Reissue ............................... I-I 
Section Overview ................................. I-I 
2. SYSTEM INITIALIZATION ............................ 2-I 
General ......................................... 
2-I 
3. CUSTOMER DATA ENTRY FORMS ..................... 3-1 
General ......................................... 3-l 
4. TRUNK CARD SWITCH...

Installation Forms 
LIST OF TABLES (CONT’D) 
TABLE TITLE 
PAGE 
3-19 
3-20 
3-21 
3-22 
3-23 
3-24 
3-25 
3-26 
3-27 
3-28 
3-29 
3-30 
3-31 
3-32 
4-1 
4-2 
4-3 
4-4 
5-l 
5-2 
5-3 
5-4 
5-5 
5-6 
5-7 
5-8 Form 18 - Miscellaneous System Ports .......... 3-34 
Form 19 - Call Rerouting Table 
................ 3-36 
Form 20 - ARS: COR Group Definition ........... 3-37 
Form 21 - ARS: Day Zone Definition ............ 3-38 
Form 22 - ARS: Modified Digit Table ............ 3-39 
Form 23 - ARS: Route...

Installation Forms 
1. INTRODUCTION 
General 
1.01 
This document contains the forms required to install and pro- 
gram the SX-200@ DIGITAL PABX with Generic 1000 or Generic 
1001 software. Note that these forms are not an exact replica of the 
forms displayed on the CDE terminal. Note also that those forms which 
cannot be edited are not included in this Section; specifically, Review 
List for Form 09, Review List for Form 13, Review List for Form 29, and 
Form 31, CDE Data Print. This document is used...