Mitel SX-200 DIGITAL Pabx Information Manual

CHART 5-3 
INSPECT EQUIPMENT 
Step 
1. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
9. 
10. 
11. 
12. 
13. 
14. 
15. 
16. 
17. 
18. Action Comments 
Remove keys taped to top of cabinet. 
Unlock and open cabinet front door. Ensure that cabinet doors open and 
close easily. 
Tighten all shelf retaining screws. Make sure that all components 
within the cabinet are secure and 
undamaged. 
Verify cards received against invoices. DO NOT UNPACK PCB CARTONS OR 
REMOVE cards from their antistatic 
bags at this time. 
Visually...

Shipping, Receiving, And installation information 
CHART 5-4 
INSTALL CONTROL CABINET 
Note: Ideally, a Control cabinet is installed to the left of a Peripheral cabinet (existing SX-200@ 
cabinet if upgrading). The cabinets may be separated by up to the length of the PCM cable 
which connects them together. 
Step 
1. 
2. Action 
Place the Control cabinet into its assigned 
position. 
Ensure that the doors open freely, that there 
is adequate room for access, and that the AC 
receptacle and cross-connect...

Shipping, Receiving, And Installation Information 
CHART 5-5 
VERIFY GROUND CONNECTION 
Note: 
Before installation can begin a #6 AWG green ground wire must be connected between the 
equipment location and an approved ground (metallic cold water pipe or equivalent where 
it enters building). 
Step 
1. Action 
Before plugging any cards into the cabinet, 
or connecting the Equipment Ground wire, 
ensure the equipment circuit breakers are 
turned off. 
Comments 
Do not power up the PABX. 
2. Plug the AC...

Shipping, Receiving, And Installation Information 
CHART 5-6 
INSTALL PERIPHERAL CABINET 
Step 
1. Action 
Unpack the cabinet and other items, except 
printed circuit cards. Check items received 
against packing list. 
Comments 
2. Inspect the cabinet, shelf, and other items for Ensure that the doors open and 
loose, missing, or damaged parts. close freely, and all cables are 
secure and in place. Remove 
shipping screws from rear door. 
3. Place the peripheral cabinet on the right side 
of the control...

Shipping, Receiving, And Installation information 
CHART 5-7 
INSTALL ANALOG BAY 3 KIT 
Step 
1. 
Action 
Unpack kit and inspect contents for loose, 
damaged, or missing items. 
Comments 
2. Open Control cabinet doors, set power 
switches to OFF, set main breaker on rear 
door to OFF, and remove line cord from wall 
outlet. 
3. Remove rear door fan assembly 
- unplug fan supply cord, detach cord strain 
relief at stud 
- remove door ground wire at door stud 
- remove door 
4. Remove rear door 
- unplug...

Shipping, Receiving, And Installation Information 
CHART 5-7 (CONT’D) 
INSTALL ANALOG BAY 3 KIT 
Step 
10. 
11. 
Action 
Connect the wiring harness, 2”d D.C., (pn 
103148501) between the Interconnect card 
and the PFT card. 
Interconnect Colour PFT 
TB301-1 Brown TB-3 
TB30 1-2 Blue TB-5 
TB30 1-3 
TB30 l-4 White TB-6 
‘TB30 1-5 Red TB-7 
TB30 1-6 Orange TB-4 
TB30 1-7 Yellow TB-2 
Install cutover monitor cable (pn 114905501) 
from P18 on Interconnect card to TB-7 on 
PFT card. Secure connector with a...

Shipping, Receiving, And Installation Information 
EQIJJEy;NT POLVETHVLENE 
PACKING 
PIECES 
 END 
SUPPORT 
KA0185ROEO 
Figure 5-2 Equipment Analog Shelf Packaging 
Page 5-l 1  

Shipping, Receiving, And Installation Information 
CHART 5-7 (CONT’D) 
INSTALL ANALOG BAY 3 KIT 
Step 
18. 
Action 
Connect the DC power cable leads to the 
Bay 3 backplane, as shown in Figure 4-l 1. 
Comments 
19. Connect the DC power cable to the 
Interconnect card as follows: 
TB301-1 brown 
TB301-2 blue 
TB301-3 braided gnd cable to Control shelf 
frame 
TB301-4 nc 
TB301-5 nc 
TB301-6 orange 
TB30 1-7 yellow 
20. Connect connectors from Maintenance Panel 
cable to P301 and P303 of Interconnect Card....

Shipping, Receiving, And installation information 
CHART 5-7 (CONT’D) 
INSTALL ANALOG BAY 3 KIT 
Step 
27. 
Action 
Install upper support over power supply 
hinge pin and secure to cabinet with four 
screws and lockwashers. 
Comments 
27. Connect ground lead to rear door power 
supply using hardware from original door. 
29. Plug AC distribution unit assembly supply 
cord into the power supply outlet. Attach 
cable strain relief to power supply door by 
removing power supply cover screw and 
replacing it...

Shipping, Receiving, And Installation Information 
CHART 5-8 
INSTALL BAY 3 KIT INTO AN SX-200@ UNIVERSAL CABINET 
Step 
1. Action 
Unpack kit contents and inspect for loose, 
damaged, or missing items. Comments 
2. Open Control cabinet doors, set BPS 
switches to OFF, set main breaker on rear 
door to OFF, and remove line cord from wall 
outlet. 
3. 
4. 
5. 
6. Install Interconnect card with six screws on Top right mounting hole goes to 
the upper left side of the cabinet (viewed sixth hole from top of...