Mitel SX-200 DIGITAL Pabx Information Manual

Shipping, Receiving, And Installation Information 
(b) 
id 
(d) 
(e) 
(f) 
(9) 
from a cold water pipe or other equally grounded point, using a 
#6 AWG insulated green wire connected directly to both points 
only. 
The system cabinets and associated ducting hardware shall not 
be exposed to any ground source other than that described in 
subparagraph (a) above. 
AC service wires bringing AC to the cabinets shall not share an 
enclosure or raceway with other system grounds, DC power 
distribution wires,...

Shipping, Receiving, And Installation Information 
4. CONTROL SHELF AND PERIPHERAL SHELF BACKPLANES AND WIRING 
Control Shelf 
4.01 
The Control Shelf combination backplane is an integral part of 
the Control Shelf and serves Bay 1 and Bay 2 to connect the 
various circuit cards. 
4.02 The 12 Peripheral cards are arranged in two rows; the upper 
row designated by square and circular identifications, and the 
lower row by circular identifications. Four of the Peripheral cards are 
on Bay 2 (two rows of...

Shipping, Receiving, And Installation information 
Figure 4-9 shows wiring in the peripheral cabinet. Figure 4-10 shows 
Power Fail Transfer wiring. Figure 4-11 shows Peripheral cabinet back- 
plane wiring. 
Surge Clamp 
4.07 Each Peripheral Shelf requires a Surge Clamp on its backplane 
at Slot 16, Pin 10 as shown in Figure 4-11. 
Peripheral Shelf - 336-Port Configuration 
4.08 The Universal Cabinet can be expanded by adding a Digital 
Peripheral shelf above the Control shelf; it contains Digital Bay 
3...

Shipping, Receiving, And installation Information 
L 
BAY 2 SLOT 34 BAY 1 SLOT 7+8 BAY 1 SLOT 5+6 
63 
‘@c&D ’ 
J25 
E3 (EDG) e,  0 J,3 . . . . . . e . .  52, . . . . . .,.. .WQ?  . . . . . . . ..J.3 [ 
E4 (DG) 
J23.a ABC 
0 NOT USED 
0 TEMP SENSE p 
3 . . . . Jl 
NOT USED 
10  J17A 
I PCM TO 
15  BAY 3 
20 5178 
25 PCM TO 
BAY 4 
CONSOLE 
MAINTENANCE 
0 
-z: 
+1m . 
-2nv. 
-4mJ. 
I R. 
+39p . 
-5” . 
. 
% . 
DISK DRIVE 
POWER PANEL 
. . . . 
J27 
T+R TEST LINE P3 
i 
h 
UPS ALARM UP 
‘15 El (EDG) 
Q 
E2...

Shipping, Receiving, And Installation Information 
TO DOOR -I 
NOTE: 
7696RZEi 
Figure 4-2 Rear View of SX-200@ Control Cabinet - Grounding 
Page 4-4  

Shipping, Receiving, And installation Information 
4 S”PPLY j /I t s”ppLy 
j v- 
II III Y, f- -  -- 
Figure 4-3 Rear View of SX-200@ Control Cabinet - Power 
Page 4-5  

Shipping, Receiving, And Installation Information 
- 
;: 
= -- 
. -. 
Figure 4-4 Rear View of SX-200@ Control Cabinet - Signal Cables 
Page 4-6  

Shipping, Receiving, And Installation information 
BAY 2 SLOT 3t4 
BAY 1 SLOT 7+8 BAY 1 SLOT 5+6 
IIGHT 
ELL q ONNECTION 0 
CONSOLE 
MAINTENANCE 
PANEL 
. . . . 
I 
529 
0 
T+R TEST LINE 
Jil 15 P3 
20 
25 
30 
UPS Al 
El 
0 
13 lDG)O 
.ARM UP 
BAY 2 SLOT I+2 BAY 1 SLOT 3t4 
BAY 1 SLOT It2 
NOTE: J19 = LOCAL RS-232 CONNECTOR 
ON MAINTENANCE PANEL 
521 = REMOTE RS-232 CONNECTOR 
ON CABINET REAR CABLE PANEL 
8544RlE3 
Figure 4-5 SX-200@ Universal Cabinet Control Shelf Backplane 
Page 4-7  

Shipping, Receiving, And installation Information 
Fzzzl 
-- 
8546ROEO 
Figure 4-6 Rear View of SX-200@ Universal Control Cabinet - Grounding 
Page 4-8  

Shipping, Receiving, And installation Information 
ERIPHERALA SHELF 
lTERCONNECT 
CARD’ 
CONTROL ,-’ 
SHELF ,-POWER HARNESS 
IS DRESSED 
AROUND HINGE 
 
 
I POWER 
SUPPLY 
DlSTRkTlON 
8545ROEO 
Figure 4-7 Rear View of SX-200@ Universal Control Cabinet - Power 
Page 4-9