Mitel SX-200 DIGITAL Pabx Information Manual

Shipping, Receiving, And Installation Information 
CHART 5-10 
POWER FAIL TRANSFER KIT INSTALLATION INSTRUCTIONS - UNIVERSAL CABINET 
Step 
1. 
2. 
3. 
4. 
Action 
Unlock and open rear door of cabinet. 
Attach antistatic wrist strap to your wrist 
and carefully unpack PFT card(s). 
Power down system. 
Place PFT card into position as shown in 
Figure 5-10 and identify its two mounting 
holes on frame. Remove card. 
Comments 
Figure 5-9 shows a PFT card. 
Following this sequence minimizes 
the chance of...

Shipping, Receiving, And Installation Information 
TB 
I I 
0 
OPTIONAL LWGS CONVERSION MODULE FOR PFT CARD 
853BRZE2 
Figure 5-9 Power Fail Transfer Card 
Page 5-26  

Shipping, Receiving, And Installation Information 
CARD 
FILE LOOP START 
TO 
GROUND START 
CONVERTER 
RIGHT HAND SIDE 
OF CABINET 
(FROM REAR) 
3539ROE 
Figure 5-10 Locating PFT Card in SX-200@ Cabinet 
Page 5-27  

Shipping, Receiving, And Installation Information 
FROM 
1 BACKPLANE 
J13 
TBl 
- 1 II 3LK 
i d-l 3LK 
RED 
REDJ 
7l 
KAOD56ROEO  25 PAIR CROSS-CONNECT 
BLOCK AT MDF 
I 
PAIR CROSS-CONNECT 
BLOCK AT MDF 
PAIR CROSS-CONNECT 
BLOCK AT MDF 
Figure 5-11 PFT Card Connections 
Page 5-28  

Shipping, Receiving, And Installation Information 
CHART 5-11 
INSTALL BAY 5 
Step 
1. 
Action 
Unpack shelf. Check backplane for cracks, 
bent pins, loose or missing items, and other 
damage. Check hardware against packing 
slip. Check fuses (if supplied) 
Comments 
2. Set POWER and BATTERY switches off and 
remove line cords from AC outlets. 
3. Unlock and open front door. Attach ground 
wire to side of shelf before installing shelf 
into cabinet 
4. 
5. Place shelf onto shelf guides 
Fasten shelf to...

Shipping, Receiving, And Installation Information 
Step Action 
I Comments  CHART 5-12 
PERIPHERAL CABINET RESERVE POWER SUPPLY INSTALLATION 
1. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
9. 
10. 
11. 
12. 
13. 
14. 
15. 
16. 
17. 
WARNING: Reserve supply is for peripheral 
cabinet only. DO NOT ATTEMPT TO 
CONNECT IT TO CONTROL CABINET. The 
Control Cabinet requires a UPS. 
Unpack reserve power supply equipment. 
Inspect items for damage. 
Check items received against packing slip; 
report missing items. 
Unlock .and...

Shipping, Receiving, And Install~ation Information 
CHART 5-12 (CONT’D) 
PERIPHERAL CABINET RESERVE POWER SUPPLY INSTALLATION 
Step 
18. 
19. 
20. 
21. 
22. 
23. 
24. 
25. Close and lock all cabinet doors. 
26. Place cabinet in final position. 
I Action I Comments 
Connect the Red, Black and Green leads as 
shown in Figure 5-13. 
Route the charging unit power lead to the 
adapter, and plug the adapter into the 
receptacle on the rear door power supply. 
Plug system power cord into its receptacle. 
On...

Shipping, Receiving, And Installation Information 
MOUNTING 
HOLES 
CHAdGiN, 
0606Rl E 
Figure 5-12 Charging Unit 
Page 5-32  

Shipping, Receiving, And Installation Information 
CABLE 
/ TIE 
POWER 
CORD 
ADAPTER 
0605R4E4 
Figure 5-13 Reserve Power Supply 
Page 5-33  

Shipping, Receiving, And Installation Information 
CHART 5-13 
Step 
1. 
2. 
3. INSTALL UNINTERRUPTIBLE POWER SUPPLY (UPS) 
Action 
Comment5 
Unpack, and inspect the UPS. 
Position the UPS near the PABX and its 
power receptacle. 
Install batteries and make connections, 
except to plug PABX line cord into UPS, 
according to manufacturer’s instructions. 
Step 
1. 
2. 
3. 
4. 
5. 
6. 
7. CONNECT CABLES TO SYSTEM AND CROSS-CONNECT FIELD 
Action Comments 
Install required connection blocks at Cables are for...