Mitel SX-200 DIGITAL Pabx Information Manual

Shipping, Receiving, And Installation Information 
P19. 
P18. 
I/ I 
9549ROEC  . - 
5”s0 MODEM 
0 PRINTER 1 
J 
n - 
Figure 4-8 Rear View of SX-ZOO@ Universal Control Cabinet - Signal Cables 
Page 4-10  

Shipping, Receiving, And Installation Information 
EQUIPMENT 
STATION 
e-.. i 
I 1 i STATION TIP 
I !I! TRUNK CARD TI 
RING 
I I ITRUNK CARD RI 
RING _ ITRUNK RING 
I I 
I 1 STATII DN CARD RING 
I 1 STATION RING 
I 
PART OF 
..-..,r.. Fill  1 RING 
-- .._-_. 
FIELD 
I-“VYC” rYlL TRANSFER CABLE / POWER FAIL 
P20 
OR 
P21 
(MALE) 
PABX EQUIPMENT CABLE 
0260RlEl 
Figure 4-10 Power Fail Transfer Wiring Diagram 
Page 4-12  

Shipping, Receiving, And Installation information 
c “mtrrcn cnm, c L, T”.“C” c.Yr)LL ROM POWER SIJPPLV 
 NOTE: IF UPGRADING AN EXISTING SYSTEM TO BECOME A PERIPHERAL 
CABINET, REMOVE CABLES PlOl AND P102 (SHOWN REMOVED) 
TBl 
-lOV -5V OV +BV +BV 
INTER SHELF 
POWER CABLE 
HARNESS -b hh>// BROWN 
LORANGE I 
l II I III GRAV&i 
k!- BLUE 
BRAIDEd STATIC 
GROUND CABLE #2 
TO INTERCONNECT CARD FILE 
GROUND 
CARD FILE 
GROUND 
SURGE 
CLAMP 
PCB SIDE VIEW 
TO GROUND 
STUD 
b BROWN (NC) 
01 1BRBEB 
Figure 4-l 1...

Shipping, Receiving, And Installation Information 
i 
8 
3 BAV 3 
BAY 4 
J 8r 
i 
J 
. 
BAV 2 BAY 1 
-IL 
I- 
- AC DISTRIBUTION 
- 
- 
1-1 
==j-J AC POWER CABLES 
m GROUND WIRES =(10 TO FANS 
n FROM LINE 
FILTER 
KA0130ROEO 
Figure 4-12 AC Distribution and Grounding within a Universal Cabinet with a Digital 
Peripheral Shelf 
Page 4-l!  

Shipping, Receiving, And Installation Information 
BAV 3 
PCM CABLE- 
MAINTENANCE / 
PANEL AND 
CONNECTORS 
HARNESS THERMAL SENSOR 
AND HARNESS 
I I I PI J II I 
I ca 
I II 
BAV 4 
/PCM CABLE 
. FT CABLE 
P--J- ; -. I --- 
Figure 4-13 Signal Cables (except to MDF) within a Universal Cabinet with a Digital 
Peripheral Shelf 
Page 4-l 5/l 5  

Shipping, Receiving, And Installation information 
5. INSTALLATION CHARTS 
5.01 
Follow the Installation Charts, in sequence, to install an 
SX-200@ DIGITAL PABX. Skip those charts for equipment that is 
not being installed at this site. 
5.02 Section MlTL9 108-093-2 1 0-NA, Customer Data Entry, describes 
how to enter data into the system to make it operational. 
Installation Forms, Section MITL9108-093-206-NA includes Tip and 
Ring assignment forms for all card positions in the system. 
Precautions...

Shipping, Receiving, And Installation Information 
System Configuration 
5.06 The System Configuration identifies all equipment that is part of 
this installation, defines where each is located within the PABX, 
and to which circuit or equipment each is connected external to the 
PABX. The Configuration also identifies the information that must be 
programmed into the database to define this equipment to the proces- 
sor. 
Printed Circuit Card Distribution 
5.07 When assigning printed circuit cards...

Shipping, Receiving, And Installation Information 
CHART 5-1 
PREPARE SYSTEM CONFIGURATION 
Step 
1. Action 
Identify all stations, trunks, and other 
equipment to be connected to the system. Comments 
This information may be prepared 
before the installation begins, by a 
customer service representative for 
the installer. 
2. Determine the quantities and types of printed 
circuit cards to be installed. 
3. 
4. 
5. Assign stations and trunks to specific cards 
This ensures proper handling and 
and...

Shipping, Receiving, And installation Information 
WOODEN 
PALLET -SECURING 
STRAPS 
‘TOP CAP 
BOLSTER 
SHOCK- 
.ABSORBING 
BASE 
SHOCK- 
ABSORBING 
BASE 
KA0187ROEl 
Figure 5-l Remove External Packaging 
Page 5-4