Lucent Technologies Intuity CONVERSANT System Version 7.0 Guide

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 237
Intelligent 
Transfer Actions•To Initiate 
Transfer
•To Complete 
Transfer
FW
HFW
HFW
HFW
HFW
HFW
H
To Reconnect 
Caller
•No Answer
•Busy
FP
FPFPF
FPFFPF
FPFPF
†
FPF
†
FP
‡
FP
‡
FPF
†
FPF
†
* Appears only when Text-to Speech is installed.
† Values represented support DEFINITY G3 switch.
‡ Values represented support DEFINITY G2 switch. Table 24. Default...

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 238
Table Key:•
TT = touch-tone signaling
•
DP = dial-pulse signaling
•
F = switch hook flash; the valid range for all switches is 0–1550 
milliseconds
•
W = wait for dial tone; if there is no dial tone after 5 seconds, an error 
conditions exists
•
P = pause for 3 seconds
•
H = hang-up (onhook)
Set Analog Interfaces Parameters
Use the following procedure to set...

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 239
Standard Analog 
Interface 
Parameters1  
Start at the Switch Interfaces menu (Figure 126 on page 231
) and select
The system displays the Analog Interfaces window (Figure 127 on page 
232
).
2  
Enter the length of flash duration in the 
Switch Hook Flash Duration:
 
field.  Valid values are 0–1550 milliseconds.
Note:Flash is a short, on-hook interval...

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 240
Any adjustment occurs before the system processes the incoming speech 
for coding it later for playback.  The value in the 
Incoming Speech 
Volume: 
field represents a gain applied to the speech input using a  
logarithmic scale.  A value of 1000 equals no gain; that is, the input is 
coded at the same level as it is received.  Multiplying by 1.414 (the...

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 241
6  
Enter the volume adjustment for all outgoing speech played on analog 
circuit cards in the 
Outgoing Speech Volume:
 field.  Valid values are 
0–32000.  The default value for analog (tip/ring) circuit cards is 1000.
The value in this field and its effect are the same as for the 
Incoming 
Speech Volume: 
field.  Any adjustment is applied to recorded...

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 242
8  
Enter Yes or No in the 
Dial Tone Training: 
field to specify system 
training for existing dial tones. The default is Yes.
If this field is set to “Yes,” dial tone training is performed on each analog 
circuit card when the voice system is started or the state of the circuit card 
is changed to “inserv.”  If the field is set to “No,” default dial-tone...

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 243
Intelligent Transfer 
Actions1  
Enter one or more code letters from Table 26 on page 244
 in the 
To 
Initiate Transfer:
 field. 
If you are using a DEFINITY switch with tip/ring circuit cards, FW is the 
default.
2  
Enter one or more code letters from Table 26 on page 244
 in the 
To 
Complete Transfer:
 field. 
If you are using a DEFINITY switch with...

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 244
5  
Press 
F3
 (Save). 
The system displays the following message:
In order for the Analog Interface Parameters to be effective, 
execute Stop Voice System.  For changes to Transfer Sequences 
to be effective, any installed applications must be 
reinstalled.
Press ENTER to continue.
6  Press 
ENTER
.
The system saves the specified analog switch parameters....

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 245
Print Analog Interface Information
Use the following procedure to print analog interface information:1  
Start at the Analog Interfaces window (Figure 127
) and press 
F8
 (Chg-
Keys).
The system displays the alternate function keys.
2  
Press 
F6
 (Print).
The system prints the selected analog interface information.
Note:This information does not print if a...

5  
Switch Interface Administration  Analog Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 246
These choices appear in the PBX Defaults menu (Figure 128 on page 233
) if 
these packages are installed on the system. Select the DEFINITY switch 
choice for the country when you are connecting the voice system to a 
DEFINITY switch or select the telephone network package for that country if 
you are connecting the voice system to the public switch network....