Lucent Technologies Intuity CONVERSANT System Version 7.0 Guide

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 257
Assign Line Side DEFINITY Protocol to Digital Circuit CardsNote:Before a new protocol can be assigned to a circuit card, any 
existing protocol must first be “unassigned.” See Unassign Line 
Side DEFINITY Protocol to Digital Circuit Cards
 on page 268
 for 
more information.
Before attempting to make any assignment changes to circuit 
cards, they must be in...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 258
Figure 132. Assign Card:  Line Side DEFINITY Window
2  
Enter the circuit card number in the 
Card Number:
 field, or press 
F2
 
(Choices) to select from a menu. Initially, all fields are populated with the 
default values for the circuit card number entered.
The 
Card Number:
 field is blank in Figure 132 on page 258
. After you 
enter the circuit card...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 259
The LSE1-specific fields are:~
Idle Code
~
A-LAW or MU-LAW
~
CRC
The LST1-specific field is:
~
CSU Distance
3  
Enter the name of the country in the 
Country: 
field, or press 
F2
 
(Choices) to select from a menu.
4  
Enter Yes to enable or No to disable in the 
DTMF Muting:
 field, or press 
F2
 (Choices) to select from a menu. Yes is the default.
Enter...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 260
6  
Enter the duration of the on-hook signal used to initiate a transfer in the Switch Hook Flash Duration:
 field.   Valid values are multiples of 10 
ranging from 10–2550.  If you enter a value that is not a multiple of 10, the 
value is rounded down.   The default is 700 milliseconds.
7  
Enter the volume adjustment for all incoming speech on analog...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 261
Note:The incoming speech volume value is set on a per card basis for 
digital circuit cards, versus on a system wide basis for analog 
circuit cards.8  
Enter the volume adjustment for all outgoing speech played on the circuit 
card in the 
Outgoing Speech Volume:
 field. Valid values range from
0–32000. The default is 707.
The value in this field and its...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 262
Note:For blind transfers to work with the Line Side DEFINITY protocol, 
you must set the 
To Initiate Transfer:
 field to “FW”, and the 
To Complete Transfer:
 field to “H,” in the Analog Interface 
window. See Set Analog Interfaces Parameters
 on page 238
 for 
more information.
U.S. and Canada: Intelligent transfer (full call classification 
analysis –...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 263
12  
(LSE1 only) Enter the 8-digit code generated when the channel is idle in 
the 
Idle Code:
 field.
13  
(LSE1 only) Enter A-LAW or MU-LAW in the 
A-LAW or MU-LAW:
 field.
14  
(LSE1 only) Enter Yes to enable the cyclical redundancy check error 
checking or No to disable the error checking in the 
CRC: 
field. 
15  
Press 
F3
 (Save).
The system saves the...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 264
Use the following procedure to change the Line Side DEFINITY parameters:1  
Start at the Line Side DEFINITY menu (Figure 131 on page 256
) and 
select
The system displays the Change Parameters: Line Side DEFINITY 
window (Figure 133 on page 264
).
Figure 133. Change Parameters:  Line Side DEFINITY Window> Change Parameters 

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 265
2  
Enter the circuit card number in the 
Card Number:
 field, or press 
F2
 
(Choices) to select from a menu. Initially, all fields are populated with the 
current values for the circuit card number entered.
The 
Card Number:
 field is blank in Figure 133 on page 264
. After you 
enter the circuit card number, certain fields disappear depending on the...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 266
Display Line Side DEFINITY ParametersThe digital circuit card must first be assigned to the Line Side DEFINITY 
protocol to use this procedure. See Assign Line Side DEFINITY Protocol to Digital Circuit Cards
 on page 257
, for more information about making the 
initial assignment.
Use the following procedure to display the Line Side DEFINITY parameters of 
a...