Lucent Technologies Intuity CONVERSANT System Version 7.0 Guide

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 307
3  
Enter Yes to enable or No to disable in the 
DTMF Muting:
 field, or press 
F2
 (Choices) to select from a menu. Yes is the default.
Enter Yes to use dual-tone multifrequency (DTMF) muting to reduce false 
DTMF recognitions that sometimes result from the network echoing back 
sounds that the voice system falsely recognizes as touch tones.
Enter No when...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 308
8  
Enter addressing to be used with outgoing calls, either DTMF, MF, or 
DECADIC in the 
Outgoing Addressing Type:
 field.   The default value 
is DTMF.
9  
Enter addressing to be used with incoming calls, either DTMF, MF, or 
DECADIC in the 
Incoming Addressing Type:
 field.   The default value 
is DTMF.
10  
Enter signaling to be used with outgoing calls,...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 309
To decrease the incoming speech volume, multiply by 0.707 to 
approximately half the value or decrease it by 3 dB.  Therefore, a value of 
707 in the field reduces the volume by half, 500 by half a second time, 
etc. 
See Table 33 on page 338
 for the relationship between the volume 
number and the actual change in volume expressed in decibels.
Note:The...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 310
Change T1 A/B 
Robbed-bit E&M 
Parameters
The circuit card must first be assigned to the T1 A/B Robbed-bit E&M 
protocol to use this procedure. See Assign T1 A/B Robbed-bit E&M to Digital Circuit Cards
 on page 304
 for more information about making the initial 
assignment.
Note:Before attempting to make any assignment changes to circuit 
cards, they must be...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 311
Figure 153. Change Parameters:  T1 A/B Robbed-bit E&M Window
2  
Enter the circuit card number in the 
Card Number:
 field, or press 
F2
 
(Choices) to select from a menu. Initially, all fields are populated with the 
default values for the circuit card number entered.
The 
Card Number:
 field is blank in Figure 153 on page 311
. After you 
enter the circuit...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 312
3  
Change any of the parameters as described in Assign T1 A/B Robbed-bit E&M to Digital Circuit Cards
 on page 304
.
4  
Press 
F3
 (Save).
The system changes the protocol parameters on the selected circuit card.
Display T1 A/B 
Robbed-bit E&M 
Parameters
The circuit card must first be assigned to the T1 A/B Robbed-bit E&M 
protocol to use this procedure....

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 313
Figure 154. Display Parameters:  T1 A/B Robbed-bit E&M Window  2  
Enter the circuit card number in the 
Card Number:
 field, or press 
F2
 
(Choices) to select from a menu. Initially, all fields are populated with the 
default values for the circuit card number entered.
The 
Card Number: 
field is blank in Figure 154 on page 313
. After you 
enter the...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 314
The system displays the parameter values for the selected circuit card.
3  
Press 
F6
 (Cancel) to return to the T1 A/B Robbed-bit E&M menu.
Unassign T1 A/B 
Robbed-bit E&M to 
Digital Circuit Cards
Note:Before attempting to make any assignment changes to circuit 
cards, they must be in the MANOOS state. See Equipment State
 
on page 150
 in Chapter 3,...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 315
Figure 155. Unassign Card: T1 A/B Robbed-bit E&M Screen  
2  
Enter the circuit card number in the 
Card Number:
 field, or press 
F2
 
(Choices) to select from a menu.
The system displays the current parameter values for the selected circuit 
card.
3  
Press 
F3
 (Save).
The system removes the T1 A/B Robbed-bit E&M assignment from the 
selected circuit...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 316
ISDN-PRI Layer 1 ProtocolAccess the ISDN-
PRI Layer 1 Menu
Note:All selected options must match the corresponding options on the 
network switch, otherwise service problems can occur.
Use the following procedure to access the ISDN-Primary Rate Interface 
(ISDN-PRI) Layer 1 menu:1  
Start at the Digital Interfaces menu (Figure 129 on page 248
) and select...