Lucent Technologies Intuity CONVERSANT System Version 7.0 Guide

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 297
Change E1 CAS P2 - Australian Network ParametersThe E1 circuit card must first be assigned to the E1 CAS P2 - Australian 
Network protocol to use this procedure. See Assign E1 CAS P2 - Australian Network Protocol to E1 Circuit Cards
 on page 294
, for more information 
about making the initial assignment.
Note:Before attempting to make any assignment changes...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 298
Figure 148. Change Parameters:  E1 CAS P2 - Australian Network Window
2  
Enter the circuit card number in the 
Card Number:
 field, or press 
F2
 
(Choices) to select from a menu. Initially, all fields are populated with the 
current values for the circuit card number entered.
3  
Change any of the parameters as described in Assign E1 CAS P2 - Australian...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 299
Display E1 CAS P2 - Australian Network ParametersThe E1 circuit card must first be assigned to the E1 CAS P2 - Australian 
Network protocol to use this procedure. See Assign E1 CAS P2 - Australian Network Protocol to E1 Circuit Cards
 on page 294
, for more information 
about making the initial assignment.
Use the following procedure to display the E1 CAS P2...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 300
Figure 149. Display Parameters:  E1 CAS P2 - Australian Network Window
2  
Enter the circuit card number in the 
Card Number:
 field, or press 
F2
 
(Choices) to select from a menu.
The system displays the parameter values for the selected circuit card.
3  
Press F6 (Cancel) to return to the E1 CAS P2 - Australian Network menu. 

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 301
Unassign E1 CAS P2 - Australian Network Protocol to E1 Circuit CardsNote:Before attempting to make any assignment changes to circuit 
cards, they must be in the “manoos” state. See Equipment State
 
on page 150
 in Chapter 3, 
Voice System Administration
 , for 
additional information.
Use the following procedure to unassign the E1 CAS P2 - Australian...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 302
Figure 150. Unassign Card:  E1 CAS P2 - Australian Network Window
2  
Enter the circuit card number in the 
Card Number:
 field, or press 
F2
 
(Choices) to select from a menu.
The system displays the current parameter values for the selected circuit 
card.
3  
Press 
F3
 (Save).
The system removes the E1 CAS P2 - Australian Network assignment 
from the...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 303
T1 A/B Robbed-bit E&M Protocol
Make sure that the switch to which the system is connected is programmed 
with the following options: •
The T1 interface uses wink start robbed-bit E&M signaling on a link using 
D4 framing with zero code suppression (ZCS).  
•
The E1/T1 interface outpulses dual tone multifrequency (DTMF) tones at 
7 pulses per second when...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 304
Figure 151. T1 A/B Robbed-bit E&M Menu
Assign T1 A/B 
Robbed-bit E&M to 
Digital Circuit CardsNote:Before a new protocol can be assigned to a circuit card, any 
existing protocol must first be unassigned. See Unassign T1 A/B 
Robbed-bit E&M to Digital Circuit Cards
 on page 314
 below for 
more information.
Before attempting to make any assignment changes to...

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 305
Use the following procedure to assign the T1 A/B Robbed-bit E&M protocol to 
a digital circuit card:1  
Start at the T1 A/B Robbed-bit E&M menu (Figure 151 on page 304
) and 
select:
 
The system displays the Assign Card: T1 A/B Robbed-bit E&M window 
(Figure 152 on page 306
).
> Assign Card 

5  
Switch Interface Administration  Digital Interfaces
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 306
Figure 152. Assign Card:  T1 A/B Robbed-bit E&M Window  2  
Enter the circuit card number in the 
Card Number:
 field, or press 
F2
 
(Choices) to select from a menu. Initially, all fields are populated with the 
default values for the circuit card number entered.
The 
Card Number:
 field is blank in Figure 152 on page 306
. After you 
enter the circuit card...