Lucent Technologies Ds1/Cept1/Isdn Pri Reference Manual

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-7 G3V2 Administration 
6
The c hoic e of isdn-ext
 req uires the c irc uit p ac k be a TN767, 
TN464B or TN464C or later release DS1/CEPT1 interfac e. This 
c hoic e will enab le the board  to use ISDN sig naling  with the D 
c hannel assoc iated  with a d ifferent DS1/CEPT1 interfac e.
The c hoic e of the isdn-pri
 p arameter along  with Bit Rate
 set 
to 1.544
 selec ts the 24 Channel ISDN interfac e. This req uires 
that the c irc uit p ac k b e a TN767 or TN464C or later release 
DS1/CEPT1 interfac e on G3iV2 or a TN464C or later on a 
G3rV2. This c hoic e will enab le ISDN-PRI sig naling  to b e c arried  
over the 24th c hannel of the DS1/CEPT1 interfac e, and  will 
c ause the Country Protocol
 and  Connect
 field s to ap p ear.
The c hoic e of the isdn-pri
 p arameter along  with Bit Rate
 set 
to 2.048
 selec ts the 32 Channel ISDN interfac e. This req uires 
that the c irc uit p ac k b e a TN464C or later release DS1/CEPT1 
interfac e. This c hoic e will enab le ISDN-PRI sig naling  to b e 
c arried  over the 16th c hannel of the interfac e, and  will c ause 
the Country Protocol
 and  Connect
 field s to ap p ear.
The c hoic e of the robbed-bit
 p arameter selects a signaling  
mod e that is used for tie, CO or DID trunks, or for 56 kb p s d ata 
trunks, suc h as for Ac c unet Switc hed  56 servic e. 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-8 G3V2 Administration 
6
Country 
Protoc olG3V2 only
Va l u e s :
A numb er from 1 to 17. Default is 1
.
Re f e re n c e :
Se c t io n  ‘‘Country-Sp ec ific  Layer 3 in G3V2’’ in Chap ter 5, 
‘‘Layers 2 and 3’’.
This field  will only b e d isp layed  if the Signaling Mode
 is 
isdn-pri
, isdn-ext
, or CAS
. This field  is used  for ISDN c alls and  
for non-ISDN c alls. For ISDN-PRI the field  is used  to spec ify the 
layer 3 PRI imp lementations ap p lic able for the selec ted  
c ountry. For non-ISDN it is used  to ind ic ate to the firmware what 
sig naling  p rotoc ol to use for CAS/CO c alls. Following  is the 
mapping of country protoc ol option to country:
Option   Country
1        United States
2        Australia
3        Japan
4        Italy
5        Netherlands
6        Singapore
7        Mexico
8        Belgium
9        Saudi Arabia
10       United Kingdom
11       Spain
12       France
13       Germany
14       Czechoslovakia
15       CIS (Russia)
16       Argentina
17       Greece
All entries are valid , thoug h only some make sense. For 
example, if the user c onfig ures this DS1/CEPT1 for CAS/CO 
op eration, only spec ific  c ountries are log ic al c hoic es for the 
c ountry p rotoc ol. This is d ue to the limitation of whic h c ountries 
spec ific  DS1/CEPT1 b oard s are c ap ab le of op erating in as 
CAS/CO c onfig urations. Thus, you c an enter any c ountry 
p rotoc ol. If the c ountry p rotoc ol value c hosen is not one whic h 
is rec og nized  for CAS/CO operation, the DS1/CEPT1 software 
will d ownlink the b est c hoic e for c ountry p rotoc ol for CAS/CO 
op eration. Eac h c ountry will b e map p ed  to a sp ec ific  c ountry 
for CAS/CO operation which best fits its operation. This 
map ping  is c hosen b ec ause it most c losely follows CCITT 
spec ific ations. 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-9 G3V2 Administration 
6
Connec tVa l u e s :
host
network (d efault)
pbx
Re f e re n c e :
Se c t io n  ‘‘User-Network and  Peer Protoc ols’’ in Chapter 5, 
‘‘Layers 2 and 3’’.
Th e  Connect
 field  will only ap p ear if isdn-pri
 signaling is 
c hosen. This field  ind ic ates what is on the far end  of the PRI in 
ord er to c ontrol the layers 2 and  3 p rotoc ol p rop erly (see the 
following description of the Interface
 field ). The d efault value 
for this field  is network
. Network means that the trunks on this 
b oard  are c onnec ted  to a p ub lic  network switc h. Bec ause the 
p ub lic  network ISDN PRI p rotoc ol d iffers from c ountry to 
c ountry, a value of network here c auses the c ountry p rotoc ol 
field  to ap p ear in G3V2 systems, allowing  you to c hoose the 
c orrec t p rotoc ol. Similarly, if you ad minister host
, it means that 
the system is c onnec ted to a c omp uter of some kind . Ag ain, the 
c ountry p rotoc ol field  ap p ears in G3V2 systems. In G3V2 
systems in the U.S. (c ountry op tion 1) a value of network means 
the system is the user sid e in a user-network protoc ol and  a 
value of host means the system is the network sid e in a 
user-network p rotoc ol. If the Connect
 value is pbx
, it means 
the interfac e is c onnec ted  to another PBX, whic h d oes not 
nec essarily have any relationship  to the c ountry in whic h the 
system resides. Thus, instead  of the c ountry p rotoc ol field  
appearing, the field Interface
 ap p ears. In G3V2 systems, 
this field  allows you to c hoose a user-network p rotoc ol or a p eer 
p rotoc ol for PBX-to-PBX c onnec tions. If a p eer p rotoc ol is 
ad ministered , the c ountry p rotoc ol is not need ed bec ause a 
spec ific  p eer p rotoc ol (ECMA) has b een imp lemented . If a 
user-network p rotoc ol is c hosen, however, the c ountry p rotoc ol 
is relevant and  this field  will ap p ear in G3V2 systems. 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-10 G3V2 Administration 
6
InterfaceVa l u e s :
network
p eer-master (G3V2 only)
p eer-slave (G3V2 only)
user (d efault)
Re f e re n c e :
Se c t io n  ‘‘User-Network and  Peer Protoc ols’’ in Chapter 5, 
‘‘Layers 2 and 3’’.
This field  will only ap p ear if pbx
 is c hosen as the Connect
 
value. If you administer user
, the system is user at b oth layers 2 
and 3 in a user-network p rotoc ol for ISDN PRI c alls on trunks on 
this interfac e. If you ad minister network
, the system is network 
at layers 2 and  3 in a user-network p rotoc ol. If you ad minister 
peer-master
, the system is a master at layer 2 in the ECMA 
p eer p rotoc ol. If you ad minister peer-slave
, the system is a 
slave a layer 2 in the ECMA p eer p rotoc ol. When you ad minister 
user or network, the c ountry protoc ol field  app ears in G3V2 
systems. When you administer either peer-master or 
p eer-slave, two field s, peer protocol
 and side
, ap pear. 
The only c hoic e, and  thus the d efault, for the p eer p rotoc ol is 
the value ECMA
. Ad ministering  the system as side A means 
that the system is the A sid e at layer 3 in the ECMA p eer 
p rotoc ol. Similarly, ad ministering  the system as sid e B means 
that it is sid e B at layer 3 in the ECMA p eer p rotoc ol. For the 
p urp oses of hand ling glare, sid e A is roug hly eq uivalent to the 
network sid e at layer 3 and sid e B roug hly eq uivalent to the 
user sid e. Note that with the p eer p rotoc ol the layer 2 
ad ministration is not linked to the layer 3 administration.
NOTE:
When a G3V2 DS1/CEPT1 interfac e ad ministered  with a 
user-network p rotoc ol is c onnec ted  to a G2.2 interfac e, 
the G3V2 interfac e must b e ad ministered  as network and  
the G2.2 interfac e as user. This is b ec ause the 
user-network ad ministration on the G2.2 is only 
imp lemented  for layer 2. The layer 3 user/network 
relationship  in G2.2 is user b y default, whic h means the 
layer 3 user/network id entific ation must b e network in the 
G3V2, whic h in turn means the layer 2 user/network is 
also network, whic h in turn means the layer 2 
user/network on the G2.2 must be user. If a G3V2 
ad ministered  for the ECMA p eer p rotoc ol is c onnec ted  to 
a G2.2, you must make sure that if the G2.2 is 
ad ministered  as user at layer 2 then the G3V2 is 
ad ministered  as p eer-master and c onversely, as p eer 
slave if the G2.2 is network. The following  tab le shows the 
rec ommend ed  ways to ad minister the user-network and  
peer p rotoc ols when a G2.2 is c onnec ted  to a G3V2: 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-11 G3V2 Administration 
6
G2.2 G3V2
Administered as Layer 2 Layer 3 Administered as Layer 2 Layer 3
user user user network network network
user user user peer-master/side A (G3V2 only) master side A
network network network p eer-slave/sid e B (G3V2 only) slave sid e B
NOTE:
When c onnec ting two DEFINITY systems via ISDN PRI, 
you should  use the user-network p rotoc ol and  c ountry 
op tion 1 if you want the extra features sup p orted by 
option 1.
Interc onnec t  G3V2 only
Va l u e s :
CO
p b x (d efault)
This field  will only ap p ear if CAS
 signaling mode is 
ad ministered . This parameter selec ts the trunk sig naling  mod e 
that the b oard  will sup p ort. 
If pbx
 is selec ted , the board  will op erate as a d ig ital tie trunk 
b oard ; if CO
 is selected, the board will operate as a digital 
CO/DID trunk b oard .
Interface 
Comp and ingG3V2 only
Va l u e s :
alaw
mulaw (d efault)
Re f e re n c e :
Se c t io n  ‘‘Comp and ing ’’ in Chapter 4, ‘‘Physical Layer’’.
This field  will only b e d isp layed  if the DS1/CEPT1 interfac e is a 
TN464C or later release. This is the only DS1/CEPT1 board  that 
allows selec tab le c omp and ing . All other DS1/CEPT1 b oard s 
op erate in either alaw or mulaw. The TN722, TN722B, and  
TN767 are mulaw c omp and ing . 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-12 G3V2 Administration 
6
CRC G3V2 only
Va l u e s :
no (d efault)
yes
This field  will only ap p ear if CAS
 is c hosen as the sig naling  
mod e. The CRC
 field ind ic ates whether the c yc lic al red und anc y 
c hec k is to b e d one on the b oard .
Idle Code G3V2 only
Va l u e s :
An 8-d ig it b inary numb er in the rang e 00000000 to 11111111. 
Default is 11111111.
Re f e re n c e :
Se c t io n  ‘‘Id le Cod e’’ in Chap ter 4, ‘‘Physic al Layer’’.
This field  enab les the c ustomer to ad minister the id le c od e 
c hannel for all c ountry p rotoc ols. The id le c od e b it p attern c an 
b e administered  to b e any p attern of 0s or 1s whic h is eight 
c harac ters in leng th, with the least sig nific ant b it in the farthest 
rig ht p osition. The expec ted value of the id le c od e for the far 
end is d etermined  b y the sp ec ific  equip ment loc ated  at the 
remote end . The following  list shows a few examp les of the id le 
c ode for sp ec ific  c ountries; for c ountries that d o not d efine the 
id le c od e, the d efault value of domestic  id le c od e 11111111 will 
be used.
United States  11111111
Australia      11111111
Italy          01010100
Japan          at least 3 1s must be administered
Th e  Idle Code
 field ind ic ates the sig nal that is transmitted  on 
all DS0 c hannels on a DS1 that have been ad ministered  to a 
c hannel g roup  or as an ac c ess endp oint, b ut are not c arrying  
an ac tive c onnec tion. 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-13 G3V2 Administration 
6
DMI-BOSVa l u e s :
no
yes (d efault)
Re f e re n c e :
Se c t io n  ‘‘Channel Struc ture and  Sig naling ’’ in Chap ter 4, 
‘‘Physic al Layer’’.
This field only appears when the Bit Rate
 is 1.544
. DMI-BOS 
y
 selec ts a mode of op eration that is c omp atib le with the 
DMI-BOS stand ard . Its use req uires a TN722B or TN767 c irc uit 
pack and common-chan
 sig naling  mod e. It also c an use a 
TN464C or later release DS1/CEPT1 b oard , c onfig ured  with 
Bit Rate
 set to 1.544
 and Signaling Mode
 set to 
common-chan
. If the Signaling Mode
 is anything  other than 
common-chan
 then the field  d isap p ears.
Slip  Detec tion
Va l u e s :
no (d efault)
yes
If frame slip  d etec tion is enab led , then the slip -rate status of 
this c irc uit p ac k will b e used  b y maintenanc e software along  
with the status of the other DS1/CEPT1 c irc uit p ac ks to 
d etermine whether an exc essive frame slip  rate exists. 
Otherwise, the slip -rate status of this c irc uit p ac k will b e 
ig nored . The p referred  c hoic e is yes unless there is no prec ise, 
ind ep end ent c loc k at the other end  of the link, as in DMI 
servic e. In sp ite of this p referenc e, the d efault value is no, 
b ec ause it is safe; an inc orrec t no will not harm a p rop erly 
working system, b ut an inc orrec t yes mig ht trig g er unwanted  
maintenanc e rep orts and  ac tions. A y
 should  b e assig ned  if 
this interfac e is a sync hronization sourc e.
Rem ote 
Loop around  
Te s t
Va l u e s :
no (d efault)
yes
This p arameter c ontrols whether the maintenanc e software is 
p ermitted  to exec ute a remote loop -around test. This test 
should  not b e p ermitted  unless the p hysic al c onfig uration 
allows it, which requires that the DS1/CEPT1 link be connected 
to ap p rop riate eq uip ment, suc h as a DSX-1 c ross-c onnec t or a 
DMI interfac e. 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-14 G3V2 Administration 
6
Synchronization Plan Form Settings
Refer to the sec tion ‘‘Sync hronization’’ in Chap ter 4, ‘‘Physical Layer’’ for further 
information on sync hronizing  the system.
Using  the c ommand  change synchronization
, enter the stratum, either 3 or 4, 
and  the b oard  loc ations of the p rimary and  sec ond ary timing  sourc es. If you 
ad minister stratum 3, the loc ation of the stratum 3 sourc e is d isp layed. If you 
ad minister stratum 4, you c an then ad minister the loc ations of the p rimary and  
sec ond ary sourc es. The ad ministered  sourc es must b e DS1/CEPT1 b oards (not 
inc lud ing  the DS1C board ). If the form is left b lank, the timing  sourc e d efaults to 
the tone/c loc k last used  as a timing  sourc e. 
In G3iV2, the list of valid  timing  sourc es ap p ears on the form. In G3rV2, you must 
use the command list timing-sources
 for this list.
Signaling Group Form Settings 
(G3V2 Systems Only)
The signaling  g roup  form c onsists of two p arts. The first p art is p ag e 1 of the 
form. The sec ond p art is c alled  the ad ministered  NCA TSC assig nment form and  
c onsists of p ag es 2 throug h 5.
Signaling Group Form Settings — Page 1
The following  list d escrib es the administration setting s for p ag e 1 of the sig naling  
g roup  form. For further information on imp lementing  signaling  g roup s, see the 
sec tion ‘‘Fac ility-Assoc iated  and  Non-Fac ility Assoc iated  Sig naling ’’
 in Chap ter 5, 
‘‘Layers 2 and  3’’.
Group  
Numb erThis d isp lay-only p arameter reflec ts the sig naling  g roup 
numb er g iven in the c ommand  arg ument.
Associated 
Sig naling
Va l u e s :
no (NFAS)
yes (FAS—d efault)
This field  ind ic ates this is either an NFAS (Non-Fac ility 
Assoc iated  Sig naling ) sig naling g roup  or a FAS (Fac ility 
Assoc iated  Sig naling ) sig naling g roup . If FAS is selec ted , only 
the field  Primary D channel
 will b e shown on the sc reen. 
NFAS c annot b e used  on interfac es with a c ountry p rotoc ol 
other than 1
 (U.S.).
Pr im a r y  D  
c hannel
Va l u e s :
Port loc ation of the D c hannel. The d efault is b lank.
This p arameter selec ts the p rimary D c hannel in the sig naling  
g roup . 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-15 G3V2 Administration 
6
Sec ond ary D 
c hannelVa l u e s :
Port loc ation of the b ac kup D c hannel. The default is b lank.
This field will only appear if this signaling group is an NFAS 
sig naling  g roup . It ind ic ates the sec ond ary D c hannel in this 
signaling group. NFAS is supported only in country option 1.
Trunk Group  
for Channel 
Selec tionEnter a valid  ISDN PRI trunk g roup  here. In c ountries where this 
is supported, if a SETUP message is received for this signaling 
g roup  with the c hannel ID IE c od ed  as any channel
, or if a 
SETUP messag e is rec eived  with an emp ty or missing  c hannel 
ID IE, a B c hannel from this trunk g roup  will b e selec ted .
Max numb er 
of NCA TSCNOTE:
Ad ministering  this field, the next two fields, and  p ag es 2 
throug h 5, d ep end  on the ap p lic ation for whic h temp orary 
sig naling c onnec tions are being used . For G3V2 
systems, the only ap p lic ation for TSCs is in ISDN DCS. 
G3V2 systems will also tand em TSCs b eing  used  b y 
some other ap plic ation. For information on how to 
ad minister these field s for ISDN DCS, see the G3V2 
imp lementation manuals. Only c ountry op tion 1 sup p orts 
TSC s .
Va l u e s :
A numb er in the rang e 0 - 256. The d efault is 0.
Re f e re n c e :
Se c t io n  ‘‘Temp orary Sig naling Connec tions’’ in Chapter 5, 
‘‘Layers 2 and 3’’.
This is the maximum numb er of non-c all-assoc iated  temp orary 
sig naling  c onnec tions p ossib le in this signaling  g roup . This 
numb er is the sum of all the NCA-TSCs administered  on p ag es 
2 throug h 5 of this form p lus the number of NCA-TSCs 
tand emed throug h the system on this sig naling  g roup .
Max numb er 
of CA TSC
Va l u e s :
A numb er in the rang e 0-400.
Re f e re n c e :
Se c t io n  ‘‘Temp orary Sig naling Connec tions’’ in Chapter 5, 
‘‘Layers 2 and 3’’.
This is the maximum numb er of simultaneous c all-assoc iated  
temp orary sig naling  c onnec tions that c an exist in this sig naling  
g roup . A typ ic al value is the numb er of memb ers in the 
signaling group. 
						

							DEFINITY Communications System Generic 2.2 and Generic 3 V2 
DS1/CEPT1/ISDN PRI Reference  
555-025-107  Issue 1
July 1993
System Administration 
Page 6-16 G3V2 Administration 
6
Signaling Group Form Settings — Pages 2-5
Pages 2-5 of the sig naling group  form are for ad ministering NCA-TSCs. Not all 
NCA-TSCs have to b e ad ministered . The ISDN DCS feature req uires one 
NCA-TSC to b e ad ministered  p er log ic al DCS c hannel, however.
The following  list d esc rib es the ad ministration setting s for p ag es 2-5 of the 
signaling group form. For further information on implementing signaling groups, 
see the section ‘‘Fac ility-Assoc iated and  Non-Fac ility Assoc iated  Sig naling ’’
 in 
Chap ter 5, ‘‘Layers 2 and  3’’
. Trunk Group  
for NCA TSC
Va l u e s :
A valid trunk g roup  numb er. The d efault is b lank.
Re f e re n c e :
Se c t io n  ‘‘Temp orary Sig naling Connec tions’’ in Chapter 5, 
‘‘Layers 2 and 3’’.
This field  d esig nates one ISDN PRI trunk g roup  whose 
inc oming c all hand ling  tab le will be used  to hand le inc oming  
NCA-TSCs on this signaling group.
Trunk Brd Board  loc ation of the DS1/CEPT1 b oard  having  trunk g roup  
memb ers in this signaling  g roup . The d efault is blank.
This field will only appear if this signaling group is an NFAS 
signaling group. It indicates all the trunk boards having 
members belonging to this signaling group.
Interfac e ID
Va l u e s :
Interfac e ID b etween 0-31. The d efault is b lank.
This field will only appear if this signaling group is an NFAS 
sig naling  g roup . It ind ic ates the interfac e ID for the 
corresponding trunk board. In an NFAS Signaling Group, an 
Interfac e ID must b e assig ned  to eac h DS1 fac ility so that it c an 
b e referenc ed  b y both end s.
Servic e/Feature
Values:
Interfac e ID between 0-31. The d efault is b lank.
Any valid  servic e typ e d efined in the network fac ilities form.
Re f e re n c e :
Sec tion ‘‘Temp orary Signaling  Connec tions’’ in Chap ter 5, 
‘‘Layers 2 and 3’’.
This field  ind ic ates the servic e type of all the ad ministered  
NCA-TSCs on this sig naling  g roup . This servic e typ e along  with 
the trunk g roup  for NCA-TSC field from p ag e 1 d etermines 
whic h row of the inc oming  c all hand ling  tab le to ap ply to the 
NCA-TSC.