Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-5 Access the System 
3
Connecting a PC
You c an c onnec t your PC or lap top  to the DEFINITY ECS R8si/R8c si/R8r either 
d irec tly (50 ft [ 15 m]  or less) or remotely throug h a d ata mod ule or a mod em. 
Connecting directly to the DEFINITY ECS
You c an c onnec t d irec tly from the PC if it is 50 ft (15 m) or less from the 
DEFINITY ECS. 
1. Connec t the...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-6 Access the System 
3
Connecting remotely to the DEFINITY ECS
To c onnec t remotely to the system, you need  one of the following  p iec es of 
hard ware:
nConnec ting  throug h a data mod ule
nConnec ting  b y analog  mod em to INADS p ort
Connecting through a data module
If more than 50 ft (15 m) from the DEFINITY ECS, you c an c onnec t the PC throug h 
a...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-7 Access the System 
3
NOTE:
With a 7400A or 7400B+  data mod ule, use a 4-wire d ig ital line c irc uit p ac k. 
With the 8400B+  d ata mod ule, use a 2-wire d igital line c irc uit p ac k.
In p lac e of a 7400B+  d ata mod ule, you c an use a 7400A d ata mod ule. If 
you do, set the 7400A to DCE Mod e.
2. Wire the d ig ital line c irc uit p ac k to the wall...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-8 Access the System 
3
Testing Hardware Connections
In the following  tab le, find  your d ata mod ule and  follow the instruc tions for testing  
and  troub leshooting  it.
.
Setting the Data Module Operating Mode
1. Connec t an RS-232 c ab le from the DSA/DNA c omp uter to the d ata 
mod ule. If you are using  an 8400B+ , c onnec t the DSA/DNA c omp uter to...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-9 Access the System 
3
Setting the 7400B+ Options
1. Set the DIP switc hes for the 7400B+  using  Tab le 3-3. The DIP switc hes are 
loc ated  insid e the unit. To ac c ess them
a. Remove the p ower c ord  from the unit.
b . Remove the c over from the top  rear of the unit.
c . Set the d ip  switc hes.
d . Rep lac e the c over.
e. Connect the power c ord.The...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-10 Access the System 
3
1. Connec t the eq uip ment as shown in Fi g u re  3 - 5.
Figure 3-5. A typical remote connection through a modem to access a remote 
DEFINITY ECS
Follow these step s to c onnec t to the DEFINITY ECS through a mod em.
1. Connec t the c omp uter to the mod em.
2. Connec t an analog  telephone line to the left most analog -line p ort on...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-11 Access the System 
3
4. Plug  the mod em into an AC p ower outlet.
5. Turn on the modem.
6. Set the following  p ort setting s:
Table 3-4. U.S. Robotics Modem Dip Switch Settings
Dip 
Switch Setting Description
1UP
DOWNData Terminal Read y normal
Data Terminal Ready override
2UP
DOWNVe r b a l  r e s u lt  c o d e s
Numeric result codes
3UP
DOWNSuppress...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-12 Activate the System 
3
Activate the System
Instruc tions are p rovid ed  to ac tivate Release 8 and  later systems. To ac tivate a 
G3V4 and  earlier system, refer to DEFINITY Communic ations System Generic  3 
Installation and  Test.
NOTE:
To p revent unnec essary troub le tic kets, d o not enab le the system alarms 
(Alarm Orig ination feature) until all...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-13 Activate the System 
3
Figure 3-6. TN2211 Optical Drive
NOTE:
Make sure the formatted removab le med ia is not write-p rotec ted 
(see Fig ure 3-7
) b efore plac ing  it into the op tic al d rive.
Figure 3-7. Make sure the disk is not write protected Figure Notes
1. Not write protec ted 2. Write p rotec ted
Red
Green
Yellow
fpdf2211 KLC 010600TN2211 OPTICAL...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-14 Activate the System 
3
Power Up the System
AC-Powered System
1. Set the c irc uit breakers on the AC p ower p anel to ON. If the system is hig h 
or c ritic al reliab ility, p ower-up the EPN c ab inet first, then the PPN c ab inet. 
Always p ower up the PPN c ab inet last.
2. Set the c ab inet c irc uit breakers to ON. This starts the system initialization...