Lucent Technologies CentreVu Call Management System Release 3 Version 8 Software Installation And Setup Manual

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Setting Up the NTS2-173
6. Connect the power cord to the NTS (see the following figure). 

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Setting Up the NTS2-174
7. Connect the 10-T transceiver to the Network Transceiver Port on the 
back panel of the NTS.
8. Connect the network hub unit to the NTS (10-T transceiver) using a 
UTP network cable.
9. Connect a dumb terminal to the Console Port on the rear of the NTS 
using the console cable and adapter that came with the NTS. On 
the 8- and 16-port NTSs, the Console Port is port #1.
You will need the...

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Setting Up the NTS2-175
12. Enter the erase command.
There are two types of information that can be erased:
lEEPROM (configuration information)
lFLASH (self-boot image).
If only one type of information is present, the program begins to 
erase it. If there are two types of information, the program 
prompts you to select the information you want to erase. Erase 
both the EEPROM and the FLASH information.
The...

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Setting Up the NTS2-176
17. Enter the IP address for this NTS. This should follow the IP address 
structure outlined earlier in the Prerequisites
 on Page 2-172. The 
program responds:
18. Enter the appropriate Subnet mask, or press Enter to accept the 
default. The program responds:
19. Enter the IP address of the CMS computer. The program responds:
20. Press Enter to accept the default broadcast message...

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Setting Up the NTS2-177
22. Press Enter to accept the default IP packet encapsulation. The 
program returns to the monitor: prompt if you have a 64-port 
NTS. Continue with Step24
.
The program responds with the following question if you have an 8- 
or 16-port NTS:
23. Enter N. The program returns to the monitor: prompt.
24. Enter the boot command at the monitor prompt to reinitialize the 
NTS with the new...

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Setting Up the NTS2-178
25. Press Enter to accept the default boot file name. The program 
responds:
The periods (dots) continue to appear as the NTS is initialized and 
set up.
If the program displays “SELF” instead of the IP address 
(192.168.2.1 is the factory default; your IP address may be 
different), it means that you did not erase EEPROM. Go back to 
Step 12
 to erase EEPROM.
When the initialization...

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Creating an Alternate Boot Device2-179
Creating an Alternate Boot Device2
This procedure creates an alternate boot device. This procedure is 
required only for mirrored systems.
1. Log in as root and Enter:
ls -l/dev/rdsk/
where  is the device to be used as the alternate boot 
disk. This disk should already be partitioned as an alternate boot 
device, according to the partitioning instructions provided in...

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Creating an Alternate Boot Device2-180
7. Reboot once again to return system control to the regular boot disk:
/usr/sbin/shutdown -y -g0 -i6
8. To set up a cron job for chkDisk, enter:
crontab -e
The cron file is displayed in editor mode.
9.Add the following line to the end of the cron file:
15   0  *  *  *  /olds/chkDisks>/dev/null 2>&1
10. To save and quit the file, enter:
 :wq
11 . E n t e r :
chmod  +x...

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Performing a CMSADM Backup2-181
Performing a CMSADM BackupB
The CMSADM file system backup saves all of the file systems on the 
computer onto a tape. 
OverviewBThe CMSADM file system backup includes the following:
lSolaris 7 system files and programs
lCMS programs and data
lNon-CMS customer data placed on the computer (in addition to the 
CMS data).
The CMSADM file system backup should be done at the following...

  Installing Software and Setting Up CMS CentreVu®  CMS R3V8 Software Installation and Setup
Performing a CMSADM Backup2-182
Platform 
Considerations
B
lAll platforms.
PrerequisitesBlBefore starting the backup procedures described in this section, log 
in as 
root, and enter lp /etc/vfstab. The output from the printer 
is necessary when doing a system restore. Bundle the printout of 
the /etc/vfstab file with the system backup tape(s) for future 
reference.
lVerify that the computer is in a Solaris...