Lexmark X9575 User Manual

If you believe you purchased a new, genuine Lexmark print cartridge, but the Out of Original Lexmark
Ink message appears:
1Click Learn More on the message.
2Click Report a non-Lexmark print cartridge.
To prevent the message from appearing again for the indicated cartridge(s):
Replace your cartridge(s) with new Lexmark print cartridge(s).
If you are printing from a computer, click Learn more on the message, select the check box, and click Close.
If you are using the printer without a computer, press...

If you aligned the cartridges to improve print quality, print your document again. If print quality has not improved,
clean the print cartridge nozzles.
Cleaning the print cartridge nozzles
1Load plain paper.
2Press  or  repeatedly until Maintenance is highlighted.
3Press .
4Press  or  repeatedly until Clean Cartridges is highlighted.
5Press .
A page prints, forcing ink through the print cartridge nozzles to clean them.
6Print the document again to verify that the print quality has improved.
7If print...

4Using another clean section of the cloth, gently hold the cloth against the contacts for about three seconds, and
then wipe in the direction shown.
5With another clean section of the cloth, repeat step 3 and step 4.
6Let the nozzles and contacts dry completely.
7Reinsert the print cartridges.
8Print the document again.
9If the print quality does not improve, clean the print nozzles. For more information, see “Cleaning the print
cartridge nozzles” on page 182.
10Repeat step 9 up to two more times.
11If...

Removing the printer from the Tray 2 base
If you need to move the printer to a different location, be sure you first remove the printer from the Tray 2 base. This
helps to avoid damaging the printer and the base.
To safely move the printer and the optional Tray 2, follow these precautions:
Keep the printer in an upright position.
Avoid severe jarring movements that may cause damage to the printer and the tray.
1Turn the printer off, and disconnect the power cord from the wall outlet.
2Disconnect all...

4Wipe only the outside of the printer, making sure to remove any ink residue that has accumulated on the paper
exit tray.
Warning—Potential Damage: Using a damp cloth to clean the interior may cause damage to your printer.
5Make sure the paper tray and paper exit tray are dry before beginning a new print job.
Ordering supplies
Ordering print cartridges
Lexmark 9500 Series models
ItemPart numberAverage cartridge standard page yield is up to1
Black cartridge42A220
Black cartridge242220
High yield black...

PaperPaper size
Lexmark Photo PaperLetter
A4
4 x 6 in.
10 x 15 cm
Lexmark PerfectFinish Photo PaperLetter
A4
4 x 6 in.
10 x 15 cm
L
Note: Availability may vary by country or region.
For information on how to purchase Lexmark Photo Paper or Lexmark PerfectFinish Photo Paper in your country or
region, go to www.lexmark.com.
Maintaining the printer
186
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting
If you set up your printer on a wireless network, make sure:
The wireless network is working properly.
The computer and printer are both connected to the same wireless network.
The printer is within the range of the wireless network. The effective range for optimal performance is generally
100–150 feet.
The printer is located away from other electronic devices that may interfere with the wireless signal.
The power supply is connected to the printer, and  is lit.
The Wi-Fi indicator light...

DISCONNECT AND RECONNECT THE POWER CORD
1Disconnect the power cord from the wall outlet, and then from the printer.
2Plug the cord all the way into the power supply on the printer.
12
3Plug the cord into a properly grounded electrical outlet that other electrical devices have been using.
4If the  light is not on, press .
Software does not install
These are possible solutions. Try one or more of the following:
CHECK YOUR OPERATING SYSTEM
The following operating systems are supported: Windows Vista,...

REINSTALL THE SOFTWARE
1Turn off and then restart your computer.
2Click Cancel on all New Hardware Found screens.
3Insert the CD, and then follow the instructions on the computer screen to reinstall the software.
RECONNECT POWER SUPPLY
1Press  to turn the printer off.
2Disconnect the power cord from the wall outlet.
3Gently remove the power supply from the printer.
4Reconnect the power supply to the printer.
5Plug the power cord into the wall outlet.
6Press  to turn the printer on.
DISABLE ANTI-VIRUS...

RELOAD PAPER
Remove and then load paper.
CHECK INK
Check the ink levels, and install new print cartridges if necessary.
CHECK CARTRIDGES
1Remove the print cartridges.
2Make sure the sticker and tape have been removed.
12
3Reinsert the cartridges.
CHECK PRINTER DEFAULT AND PAUSE SETTINGS
1Do one of the following:
In Windows Vista, click  ŒControl Panel.
In Windows XP, click Start.
2Click Printers ΠPrinters and Faxes.
3Double-click the printer queue device.
4Click Printer.
Make sure no check mark appears...