Lexmark C 950 Service Manual
Have a look at the manual Lexmark C 950 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information 4-357 5058-030 Go Back Previous Next 3.Remove the upper media bin assembly (A). Upper media bin front cover removal 1.Remove the finisher front door assembly. See “Finisher front door assembly removal” on page 4-280. 2.Remove the upper media bin assembly. See “Upper media bin assembly removal” on page 4-356. 3.Remove the two screws securing the upper media bin front cover (A). 4.Remove the upper media bin front cover (A). Upper media exit pinch roll assembly removal 1.Open the finisher front door assembly. 2.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313. 3.Remove the upper media bin assembly. See “Upper media bin assembly removal” on page 4-356. 4.Remove the top cover. See “Top cover removal” on page 4-355. A
4-358 Service Manual 5058-030 Go Back Previous Next 5.Remove the four screws securing the four upper media exit pinch roll assemblies (A) to the finisher. 6.Remove the four upper media exit pinch roll assembly (A). Upper media exit roll assembly removal 1.Open the finisher front door assembly. 2.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313. 3.Remove the upper media bin assembly. See “Upper media bin assembly removal” on page 4-356. 4.Remove the top cover. See “Top cover removal” on page 4-355. 5.Remove the drive motor (exit). See “Stepper motor (exit) assembly and belt (exit) removal” on page 4-352. 6.Disconnect the connector from the sensor (upper media exit) (A). 7.Release the harness from the clamps. 8.Remove the two front and two rear screws securing the upper exit guide assembly (B). 9.Remove the upper exit guide assembly. RearA Left A LeftConnector
Repair information 4-359 5058-030 Go Back Previous Next 10.Remove the two front screws and the two rear screws securing the bracket (C) to the finisher. 11.Remove the bracket (C). 12.Release the hook from the upper media exit roll drive gear 20T(D). 13.Remove the upper media exit roll drive gear 20T. 14.Remove the 6 mm bushing. 15.Use a prying tool to remove the e-clip securing the upper media exit roll assembly (F) to the front of the finisher. 16.Remove the 6 mm bushing (E). Rear Front B C
4-360 Service Manual 5058-030 Go Back Previous Next 17.Move the upper media exit roll assembly frontward and outward in the direction of the arrow. 18.Remove the upper media exit roll assembly (F). Note: When removing the upper media exit roll assembly (F), do not touch the rubber surface. Reinstallation notes: •Maker sure the flat spot of the upper media exit roll assembly (F) is installed to the rear. •When replacing the upper media exit roll assembly (F), do not touch the rubber surface. Upper pinch guide assembly removal 1.Open the finisher front door assembly. 2.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313. 3.Remove the drive motor (buffer/transport). See “Stepper motor (buffer/transport) and belt (buffer/ transport) removal” on page 4-348. 4.Remove the three screws securing the hinge of the upper pinch guide assembly (A) on the rear of the finisher. 5.Move the upper pinch guide assembly hinge from the rear of the finisher. 6.Remove the upper pinch guide assembly (A) from the inside of the finisher in the direction of the arrow. Front FE-clip E Rear DF E A RearA Front
Repair information 4-361 5058-030 Go Back Previous Next Upper transport roll removal 1.Open the finisher front door assembly. 2.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313. 3.Remove the top cover. See “Top cover removal” on page 4-355. 4.Remove the left lower cover. See “Left lower cover removal” on page 4-292. 5.Remove the left upper cover. See “Left upper cover removal” on page 4-293. 6.Remove the punch carriage assembly. See “Punch carriage assembly removal” on page 4-308. 7.Open the upper pinch guide assembly (A) toward the right. 8.Remove the two screws securing the bracket (B) on the rear of the finisher. 9.Move the bracket (B) slightly toward the exit side of the finisher. Note: It is not necessary to remove the bracket from the finisher; it should only be slightly moved to provide better access to the two upper media transport roll assemblies (C) for removal. 10.Remove the two screws securing the bracket (D). Note: It is not necessary to remove the bracket from the finisher; it should only be slightly moved to provide better access to the two upper media transport roll drive pulleys 20T(E). FrontFront D A RearD B B F G F Second First
4-362 Service Manual 5058-030 Go Back Previous Next 11.Loosen the two screws securing the belt tensioner bracket (F) to the finisher, and move the bracket downward as shown. 12.Remove the belt (buffer/transport) (G) from the two upper media transport roll drive pulleys 20T (E). 13.Release the hook securing the appropriate upper media transport roll drive pulley 20T (E) to the appropriate upper transport roll (C). 14.Remove the appropriate upper media transport roll drive pulley 20T (E). 15.Remove the appropriate bushing (H). 16.With a prying tool, remove the e-clip securing the appropriate upper transport roll (C) to the front of the finisher. 17.Remove the appropriate 6 mm bushing (I). 18.Move the appropriate upper transport roll (C) toward the front and outward. 19.Remove the appropriate upper transport roll (C). Note: When removing the upper transport roll (C), do not touch the rubber surface. Replacement notes: •Make sure the flat spot on the upper transport roll (C) is installed to the rear. •When replacing the upper transport roll (C), do not touch the rubber surface. •The tension of the belt (buffer/transport) (G) is automatically adjusted by the force of the spring attached to the belt tensioner bracket (F). •Tighten the two screws in the order shown. HC E HC Rear CFront IE-clip C E-clip
Repair information 4-363 5058-030 Go Back Previous Next High capacity feeder (HCF) removals HCF caster removal 1.Remove the HCF unit from the printer. 2.Place the machine so the HCF left cover faces down. 3.Remove the three screws securing the HCF caster (A) to the unit. 4.Remove the HCF caster (A). HCF controller card PCBA removal 1.Remove the HCF rear cover. See “HCF rear cover removal” on page 4-375. 2.Disconnect all connectors from the HCF controller card PCBA (A). 3.Remove the four screws securing the HCF controller card PCBA (A) to the unit. A
4-364 Service Manual 5058-030 Go Back Previous Next 4.Remove the HCF controller card PCBA (A). HCF feed lift gear bracket removal 1.Remove the HCF media tray assembly from the printer. See “HCF media tray assembly removal” on page 4-370. 2.Remove the HCF media feed unit assembly. See “HCF feed unit removal” on page 4-366. 3.Remove the HCF feed lift motor. See “HCF feed lift motor removal” on page 4-364. 4.Remove the three screws securing the HCF feed lift gear bracket (A) to the media feed unit assembly (B). 5.Remove the HCF feed lift gear bracket (A). 6.Remove the gear lift gear 24T (C) from the HCF media feed unit assembly. HCF feed lift motor removal 1.Remove the HCF media tray assembly. See “HCF media tray assembly removal” on page 4-370. 2.Remove the HCF media feed unit assembly. See “HCF feed unit removal” on page 4-366. (PF06) (PF05) Rear(PF04) (PF03)(PF02)(PF01) (PF08)A A B C
Repair information 4-365 5058-030 Go Back Previous Next 3.Disconnect the connector from the HCF feed lift motor assembly (A). 4.Remove the four screws securing the HCF feed lift motor (A) to the HCF media feed unit assembly (B). 5.Remove the HCF media feed lift motor (A). HCF feed roll assembly removal 1.Open the HCF top door. 2.Open the HCF feed unit assembly. 3.Push the two ends of the HCF feed roll assembly (A) inward, and move it upward in the direction of the arrow to release it from the HCF media feed unit assembly (B). 4.Remove the HCF feed roll assembly (A). Note: When removing the HCF feed roll assembly (A), do not touch the rubber surface. Note: Before re-installing the HCF feed roll assembly (A), do not touch the rubber surface. A B Connector A B Front
4-366 Service Manual 5058-030 Go Back Previous Next HCF feed unit removal 1.Remove the HCF media tray assembly from the printer. See “HCF media tray assembly removal” on page 4-370. 2.Remove the two screws securing the media feed unit assembly (A) on the front side. 3.Pull the media feed unit assembly (A) out of the machine in the direction of the arrow. Note: More force to remove the media feed unit (A) may be required due to the electrical connector inside the machine. HCF left cover removal 1.Remove the five screws securing the HCF left cover (A) to the unit. 2.Remove the HCF left cover (A). A Front Guide shaft A