Lexmark C 950 Service Manual
Have a look at the manual Lexmark C 950 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information 4-197 5058-030 Go Back Previous Next 7.Remove the printhead retract door. See “Printhead retract door removal” on page 4-142. 8.Remove the inner cover. See “Inner cover removal” on page 4-3. 9.Remove the inner plate. See “Inner plate removal” on page 4-95. 10.Lift the plastic gate, and push it in to prevent the toner from spilling. 11.Release the two latches (A) connecting the upper portion of the auger. 12.Detach the lower portion (B) of the auger from the developer unit. Warning: The lower portion of the auger is prone to damage. Extra care is required in handling this part. 1 2 A B
4-198 Service Manual 5058-030 Go Back Previous Next 13.Remove the Y toner auger. Re-installation note: Ensure that the rubber sleeve (C) is attached properly to prevent toner spillage. C
Repair information 4-199 5058-030 Go Back Previous Next Tray module removal procedures Unless otherwise indicated, each removal procedure applies to TTM, 3TM, and 1TM devices. 3TM left door removal 1.Remove the tray module rear cover. See “Tray module right cover removal” on page 4-215. 2.Remove the tray module left cover. See “Tray module left cover removal” on page 4-210. 3.Remove the metal clip. 4.Lift the 3TM left door, and remove it from the machine.
4-200 Service Manual 5058-030 Go Back Previous Next Sensor (media level) removal This removal procedure applies to trays 1–4. 1.Remove the appropriate feeder unit. See “Printer tray 1 feeder removal” on page 4-141, “Tray module media feeder removal” on page 4-212, “TTM tray 4 media feeder removal” on page 4-225, or “TTM tray 3 feeder removal” on page 4-221. 2.Release the tabs (A) securing the sensor (media level) to the assembly. 3.Remove the sensor (media level). 4.Disconnect the harness (B). Sensor (media out) removal This removal procedure applies to trays 1–4. 1.Remove the appropriate feeder unit. See “Printer tray 1 feeder removal” on page 4-141, “Tray module media feeder removal” on page 4-212, “TTM tray 4 media feeder removal” on page 4-225, or “TTM tray 3 feeder removal” on page 4-221. 2.Remove the media out actuator. See “Media out actuator removal” on page 4-120. 3.Release the tab (A) securing the sensor (media out) to the assembly. 4.Remove the sensor (media out).
Repair information 4-201 5058-030 Go Back Previous Next 5.Disconnect the cable (B). Sensor (media present) removal This removal procedure applies to trays 1–4. 1.Remove the left rear lower cover. See “Left rear lower cover removal” on page 4-6. 2.Remove the MPF tray feeder. See “MPF tray feeder removal” on page 4-125. 3.Remove the MPF top cover. See “MPF top cover removal” on page 4-7.
4-202 Service Manual 5058-030 Go Back Previous Next 4.Gently detach the access cover. 5.Release the hooks (A) securing the sensor (MPF media present) to the MPF tray feeder. 6.Disconnect the cable (B) from the sensor (MPF media present). 7.Remove the sensor (MPF media present). Reinstallation note: Ensure that the access cover is properly reinstalled so that it is flush with the machine or media jamming might occur.
Repair information 4-203 5058-030 Go Back Previous Next Sensor (tray module feedout) removal This removal procedure applies to all three tray modules. 1.Open the left door. 2.Remove the two screws (A) securing the metal guide to the machine. 3.Remove the metal guide. 4.Remove the tray module upper media transport roller. See the “Tray module transport rollers removal” on page 4-217. 5.Remove the screw (B) securing the plastic bracket to the machine.
4-204 Service Manual 5058-030 Go Back Previous Next 6.Remove the plastic bracket. 7.Release the hooks (C) securing the sensor (tray module feedout) to the machine. 8.Remove the sensor. 9.Disconnect the cable (D). 10.Remove the sensor (tray module feedout). Sensor (tray module left door interlock) removal 1.Remove the left cover. 2.Open the left door. 3.Remove the two screws (A) securing the plastic cover to the machine.
Repair information 4-205 5058-030 Go Back Previous Next 4.Disconnect the cable (B) from the sensor (tray module left door interlock). 5.Remove the plastic cover. 6.Disconnect the cable (C). 7.Release the hooks securing the sensor (tray module left door interlock) to the plastic cover. 8.Remove the sensor (tray module left door interlock).
4-206 Service Manual 5058-030 Go Back Previous Next Sensor (TTM media size) removal This removal procedure can be applied to either TTM tray 3 media tray or TTM tray 4 media tray. 1.Pull the appropriate TTM media tray from the machine. 2.Remove the screw (A). 3.Disconnect the cable (B). 4.Remove the sensor (TTM media size). Sensor (TTM tray 3 feedout) removal 1.Open the left door. 2.Remove the lower tray module media transport roller. See “Tray module transport rollers removal” on page 4-217.