Lexmark C 950 Service Manual
Have a look at the manual Lexmark C 950 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information 4-207 5058-030 Go Back Previous Next 3.Remove the two screws (A) securing the plastic media guide to the machine. 4.Push the plastic media guide slightly toward the rear and pull it out from the machine. 5.Release the hooks securing the sensor (TTM tray 3 feedout) to the machine. 6.Disconnect the cable (B). Sensor (TTM tray 4 feedout) removal 1.Remove the TTM tray 4 media feeder. See “TTM tray 4 media feeder removal” on page 4-225. 2.Disconnect the cable (A).
4-208 Service Manual 5058-030 Go Back Previous Next 3.Release the hooks (B). 4.Remove the sensor (TTM tray 4 feedout). Tray module bottom cover removal 1.Remove the media tray 4. 2.Remove the two screws (A) securing the tray module bottom cover to the machine. 3.Remove the tray module bottom cover.
Repair information 4-209 5058-030 Go Back Previous Next Tray module controller PCBA removal This removal procedure applies to all three tray modules. 1.Remove the tray module rear cover. See “Tray module rear cover removal” on page 4-215. 2.Remove the six screws (A). 3.Disconnect all the cables from the tray module controller PCBA. 4.Remove the tray module controller PCBA. Installation note: After installing the replacement unit, make sure that the switches (A) are configured correctly for the option where the unit is installed into. You can also use the tabularized data (B) on the PCBA board as a guide. A B
4-210 Service Manual 5058-030 Go Back Previous Next Tray module left cover removal 1.Remove the tray module rear cover. See “Tray module rear cover removal” on page 4-215. 2.Remove the screw (A) securing the foot cover to the machine. 3.Remove the foot cover. Correct dip-switch settings for the option Input OptionSwitch Settings Switch 1 Switch 2 Switch 3 Switch 4 3-Tray Module (3TM)ON ON ON ON Tandem Tray Module (TTM)ON ON OFF ON 1 Tray Module (1TM)ON OFF ON ON
Repair information 4-211 5058-030 Go Back Previous Next 4.Remove the two screws (B). Note: Opening the tray module left door will help you remove the tray module left cover. 5.Remove the tray module left cover. Tray module lower transport motor removal This removal procedure is not applicable to TTM tray modules. 1.Remove the tray module rear cover. See “Tray module rear cover removal” on page 4-215. 2.Disconnect the cable (A). 3.Release the harness from the clamp (B).
4-212 Service Manual 5058-030 Go Back Previous Next 4.Remove the four screws (C). 5.Remove the tray module lower transport motor. Tray module media feeder removal This removal procedure can be used for the following trays: •1TM tray module •3TM tray module, tray 2 •3TM tray module, tray 3 •3TM tray module, tray 4 •TTM tray module, tray 2 1.Remove the media tray 2. 2.Open the left door.
Repair information 4-213 5058-030 Go Back Previous Next 3.Remove the screw (A) securing the bracket to the machine. 4.Remove the two screws (B) securing the tray module media feeder to the machine. 5.Disconnect the two cables (C) from the machine.
4-214 Service Manual 5058-030 Go Back Previous Next 6.Remove the two harnesses from the clamps (D). 7.Remove the tray module media feeder.
Repair information 4-215 5058-030 Go Back Previous Next Tray module rear cover removal 1.Remove the five screws (A) securing the tray module rear cover. 2.Remove the tray module rear cover. Tray module right cover removal 1.Remove the tray module rear cover. See “Tray module rear cover removal” on page 4-215. 2.Remove the two screws (A). 3.Remove the tray module right cover.
4-216 Service Manual 5058-030 Go Back Previous Next Tray module top cover removal This removal procedure applies to all three tray modules. 1.Remove the media tray 2. 2.Remove the two screws (A) securing the tray module top cover to the machine. 3.Remove the tray module top cover.