Kyocera TASKalfa 300i User Manual

Default Setting (System Menu)
8-39
8
Network Status Page 
Check the information including network interface firmware version, network address and protocol.
Service Status Page
More detailed information is available than on the Status  Page. Service personnel usually print the service status 
pages for maintenance purpose.
Use the procedure below to print a report.
1Press the  System Menu  key.
2Press [Report] and [Next] of Print Report .
3Press [Print] for the report you want to print. Printing starts.
A...

Default Setting (System Menu)
8-40
Report for Job Canceled before Sending
Print a send result report when the job is canceled before being sent.
1Press the System Menu  key.
2Press [Report], [Next] of  Result Report Setting, [Next] of Send Result Report  and then [Change] of 
Canceled before Sending .
3Press [Off], [On]. 
4Press [OK].
Downloaded From ManualsPrinter.com Manuals 

Default Setting (System Menu)
8-41
8
Adjustment/Maintenance
Adjust printing quality and conduct machine maintenance. 
• Copy Density Adjustment …8-41
• Send/Box Density Adjust …8-41
• Print Density …8-42
• Drum Refresh …8-42
• Auto Drum Refresh …8-42
• Correcting Fine Black Lines …8-43
• System Initialization …8-44
• Display Brightness …8-44
• Silent Mode …8-44
• Auto Color Correction...8-44
• Gray Adjustment...8-45
NOTE: If user login administration is enabled, you can only change the settings by...

Default Setting (System Menu)
8-42
Print Density
Adjust print density. Adjustment can be made in 5 levels.
Use the procedure below to adjust the print density.
1Press the System Menu  key.
2Press [ ], [Adjustment/Maintenance] and then [Change] of  Print Density.
3Press [1] - [5] (Lighter-Darker) to adjust density.
4Press [OK].
Drum Refresh
Refresh the drum when image blur or white spots appear on images in copies.
There are 2 drum refresh modes.
NOTE: Drum Refresh cannot be performed while printing....

Default Setting (System Menu)
8-43
8
Set the duration of time to execute Auto Drum Refresh. The table below shows the available settings.
NOTE: You can also execute Drum refresh as needed (Refer to  Drum Refresh on page 8-42.)
Use the procedure below to specify  the setting for Auto Drum Refresh.
1Press the System Menu  key.
2Press [ ], [Adjustment/Maintenance], [ ] and then [Change] of  Auto Drum Refresh.
3Select [Off], [Standard] or [Long].
4Press [OK].
Correcting Fine Black Lines
Correct fine black...

Default Setting (System Menu)
8-44
Use the procedure below to specify the 
setting for correcting fine black lines.
1Press the System Menu  key.
2Press [ ], [Adjustment/Maintenance] and then [Change] of  Correcting Black Line.
3Press [Off], [On(Low)] or [On(High)].
4Press [OK].
System Initialization
Initialize the hard disk mounted on the machine to return to the default mode. 
Refer to System Initialization on page 8-63 about the initialization procedures.
Display Brightness
Set the brightness of the...

Default Setting (System Menu)
8-45
8
Gray Adjustment
After prolonged use, or from the effects of surrounding temperature or humidity, the hue of printed color output 
may shift or color drift may  occur. Use this function to correct color settings when the color of a finished copy 
does not match the original.
NOTE: To perform gray adjustment, verify that either 11 × 8 1/2 or A4 paper is loaded into a cassette.
Use the procedure below for adjustment.
1Press the  System Menu  key.
2Press [ ],...

Default Setting (System Menu)
8-46
Date/Timer 
Date/Timer settings include:
• Date/Time …8-46
• Date Format …8-46
• Time Zone …8-47
• Auto Panel Reset …8-47
• Auto Sleep …8-48
• Auto Error Clear …8-49
• Interrupt Clear Timer …8-50
NOTE: If user login administration is enabled, you can only change the settings by logging in with 
administrator privileges.
Date/Time 
Set the date and time for the location where you use the machine. If you perform Send as E-mail, the date and 
time set here will be...

Default Setting (System Menu)
8-47
8
Time Zone 
Set the time difference in the location you are from GMT. 
Use the procedure below to set the time difference.
1Press the  System Menu  key.
2Press [ ], [Date/Timer] and then [Change] of  Time Zone.
3Select the location.
NOTE: Press [ ] or [ ] to select the location.
4Press [Off] or [On] of  Summer Time and press [OK].
NOTE: If you select a region that does not utilize summer time, the summer ti me setting screen will not appear.
Auto Panel Reset
If no jobs...

Default Setting (System Menu)
8-48
Panel Reset Timer
If you select [On] for 
Auto Panel Reset, set the amount of time to wait before  Auto Panel Reset. Options are 
between 5 and 495 seconds (every five seconds).
NOTE: If you select [Off] for  Auto Panel Reset, the time display does not appear. 
Use the procedure below to set the reset time.
1Press the  System Menu  key.
2Press [ ], [Date/Timer] and then [Change] of  Panel Reset Timer.
3Press [+] or [–] to enter the time until  Auto Panel Reset is turned...