Kyocera TASKalfa 300i User Manual

Default Setting (System Menu)
8-9
8
Default Paper Source
Select the default paper source from Cassette 1-4 and Multi Purpose Tray.
NOTE: [Cassette 3] and [Cassette 4] are displayed when the optional paper feeder is installed.
Use the procedure below to sele ct the default paper source.
1Press the System Menu  key.
2Press [Common Settings], [Next] of  Original / Paper Settings and then [Change] of Default Paper Source. 
3Select a paper cassette for the default setting. 
4Press [OK].
5Move to the copy or...

Default Setting (System Menu)
8-10
3Select [All Media Types] or any media type for paper selection. 
4Press [OK].
Paper Source for Cover Paper
Select paper source for cover paper from Cassette 1-4  or Multi Purpose Tray. Cover is used for Booklet (see 
page 4-19 ) and Cover (see  page 4-21) modes. 
NOTE: [Cassette 3] and [Cassette 4] are displayed wh en the optional paper feeder is installed.
Use the procedure below to select the paper source for the cover.
1Press the  System Menu  key.
2Press [Common...

Default Setting (System Menu)
8-11
8
If you select [Adjust Print Direction], load paper according to the steps below. 
Example: copying on Letterhead
NOTE: When loading cover paper in a cassette or multi purpose tray, load the face, on which printing is 
supposed to be done, upward. 
Use the procedure below to specify the actions performed for special paper types.
1Press the  System Menu  key.
2Press [Common Settings], [Next] of  Original / Paper Settings, [ ] and then [Change] of Special Paper 
Action....

Default Setting (System Menu)
8-12
Error Handling
Select whether to cancel or continue the job when error has occurred. The possible errors and what to do for 
the errors are as follows. 
Duplexing Error 
Select what to do when duplex printing is not possible for the selected paper size and media type.
Finishing Error
Select alternative actions when finishing (stapling or of fsetting) is not available for the selected paper size or 
media type.
No Staple Error
Select what to do when staples run out...

Default Setting (System Menu)
8-13
8
Paper Mismatch Error
Select what to do when the selected paper size or type does not match paper size or type loaded in the specified 
paper source while printing from the computer by  specifying the cassette or multi-purpose tray.
Use the procedure below to specify the settings for error handling.
1Press the  System Menu  key.
2Press [Common Settings] and then [Next] of  Error Handling.
3Press [Change] at the error you wish to change the handling. 
4Select the error...

Default Setting (System Menu)
8-14
4Select Output Tray.
For [Finisher Tray], select [Face Up] (print surface up) or [Face Down] (print surface down) as the paper 
orientation at output.
5Press [OK].
6When selecting  [Face Up] (print surface up) as the paper  orientation at output, press [Page Order with Face 
Up] and then select the order of the outp ut pages from [Ascending] or [Descending].
NOTE: Selecting [Descending] accelerates the starting time of copying.
7When changing the output tray of...

Default Setting (System Menu)
8-15
8
Original Orientation
Set the original orientation defaults. The available default settings are shown below.
Refer to  page 4-10  for Original Orientation.  
Use the procedure below to select the default orie ntation when originals are placed on the platen.
1Press the System Menu  key.
2Press [Common Settings], [ ], [Next] of  Function Defaults and then [Change] of Original Orientation.
3Select [Top Edge Top] or [Top Edge Left] for the default.
4Press [OK].
Continuous...

Default Setting (System Menu)
8-16
Use the procedure below to select the default quality sett
ing for originals.
1Press the System Menu  key.
2Press [Common Settings], [ ], [Next] of  Function Defaults and then [Change] of Original Image. 
3Select the default original image.
4Press [OK].
Scan Resolution
Select the default scanning resolution. The options are 600x600dpi, 400x400dpi Ultra Fine, 300x300dpi, 
200x400dpi Super Fine, 200x2 00dpi Fine, 200x100dpi Normal.
Use the procedure below to select the...

Default Setting (System Menu)
8-17
8
2Press [Common Settings], [ ], [Next] of Function Defaults and then [Change] of Color Selection.
3Select the default color mode.
4Press [OK].
File Format 
Select the default file type to send the scanned orig inals. The available default settings are shown below.
NOTE: Refer to page 5-12 for file formats.
Use the procedure below to sele ct the default file format.
1Press the System Menu  key.
2Press [Common Settings], [ ], [Next] of  Function Defaults and then...

Default Setting (System Menu)
8-18
Density
Set the default density. The available default settings are shown below.
Use the procedure below to select the default density.
1Press the 
System Menu  key.
2Press [Common Settings], [ ], [Next] of  Function Defaults, [ ] and then [Change] of  Density.
3Select the default density. 
4Press [OK].
Zoom
Select the enlarged/reduced default when paper size/sendi ng size changed after the originals set. The available 
default settings are shown below.
Use the...