Konica Minolta bizhub C35 User Manual

Clearing Media Misfeeds 13-16
Clearing a Media Misfeed from the Fuser Unit
1Pull the lever, and then open the 
right door.
Before opening the right 
door, fold up Tray 1.
2Lift up the 2 levers.
3Open the fuser unit cover.
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds13-17
4Carefully pull out the misfed 
media.
If the misfed media cannot 
be removed by pulling it 
down, pull it from the top of 
the fuser unit.
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds 13-18
CAUTION
The area around the fuser unit is 
extremely hot.
Touching anything other than the 
indicated levers may result in 
burns. If you get burned, 
immediately cool the skin under 
cold water, and then seek 
professional medical attention.
Note
Decreased print quality may 
result if the surface of the image 
transfer belt or the transfer roller 
is touched.
Be careful not to touch the 
surface of the image transfer belt 
or transfer roller. 
Downloaded From...

Clearing Media Misfeeds13-19
5Close the fuser unit cover.
6Push down the 2 levers.
7Close the right door.
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds 13-20
Clearing a Media Misfeed from Tray 1 (Manual Feed Tray) 
and Transfer Roller
1Pull the lever, and then open the 
right door.
Before opening the right 
door, fold up Tray 1.
2Carefully pull out the misfed 
media.
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds13-21
CAUTION
The area around the fuser unit is 
extremely hot.
Touching anything other than the 
indicated levers may result in 
burns. If you get burned, 
immediately cool the skin under 
cold water, and then seek 
professional medical attention.
Note
Decreased print quality may 
result if the surface of the image 
transfer belt or the transfer roller 
is touched.
Be careful not to touch the 
surface of the image transfer belt 
or transfer roller. 
Downloaded From...

Clearing Media Misfeeds 13-22
3Close the right door.
Downloaded From ManualsPrinter.com Manuals 

Solving Problems with Media Misfeeds13-23
Solving Problems with Media Misfeeds
Frequent misfeeds in any area indicate that area should be checked, 
repaired, or cleaned. Repeated misfeeds may also happen if you’re 
using unsupported print media or original media.
Symptom Cause Solution
Several 
sheets go 
through the 
machine 
together.The front edges of 
the media are not 
even.Remove the media and even up the 
front edges, then reload it.
The media is moist 
from humidity.Remove the moist media and...

Solving Problems with Media Misfeeds 13-24
Media is mis-
fed in the 
ADF.The loaded document 
does not meet the 
specifications.Load the correct document. For details 
on the documents that can be loaded, 
refer to “Documents that can be loaded 
into the ADF” on page 4-34.
The loaded document 
exceeds the maxi-
mum capacity.Load the document so that it does not 
exceed the maximum capacity. For 
details on the documents that can be 
loaded, refer to “Documents that can 
be loaded into the ADF” on page...

Solving Problems with Media Misfeeds13-25
The recommended 
label sheet is facing 
the wrong way in Tray 
1.Load the label sheets according to the 
manufacturer’s instructions.
Envelopes are facing 
the wrong way in Tray 
1.Load the envelopes in Tray 1 with the 
flaps facing up.
If the flaps are on the long edge, load 
the envelopes with the flap edge 
toward the machine and the flap side 
facing up.
Unsupported media 
(wrong size, thick-
ness, type, etc.) is 
being used.Use KONICA MINOLTA-approved...