Konica Minolta bizhub C35 User Manual

Status, error and service messages 13-46
[I-Fax RX failed]
[Failed to complete the job 
due to an error while I-FAX 
RX.]
[Check the log.]The job did not end 
normally because an 
error occurred during 
I-FAX RX.Check the log.
[I-Fax TX failed]
[I-FAX TX failed due to 
error.]
[Redial will be attempted 
after predetermined time 
progress.]The job did not end 
normally because an 
error occurred during 
I-FAX TX.A document is sent 
again after the specified 
time period has lapsed. Message Cause Solution...

Status, error and service messages13-47 Service messages
These messages indicate a more serious problem that can only be corrected 
by a service representative. If one of these messages appears, turn the 
machine off, then on again. If the problem persists, contact your local vendor 
or authorized service provider.
Message Cause Solution
[Service Call]
[Error occurred. Power 
OFF and ON, or contact 
Service with Trouble 
Code;xxxx]An error has been 
detected with the item 
indicated by “xxxx” in 
the...

Status, error and service messages 13-48
Downloaded From ManualsPrinter.com Manuals 

14
Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 

Introduction 14-2
Introduction
Note
Use of accessories not manufactured or supported by 
KONICA MINOLTA will void your warranty.
For details of accessories, visit our web site (http://konicami-
nolta.com)
Lower Feeder Unit 
(Tray 3/Tray 4)500-sheet tray included
Working Table 
WT-P01Provides an area to temporarily place an original or 
install an authentication device.
Downloaded From ManualsPrinter.com Manuals 

Lower Feeder Unit PF-P0814-3
Lower Feeder Unit PF-P08
You can install up to one optional lower feeder unit PF-P08 (Tray 3/4). The 
lower feeder unit PF-P08 increases your machine’s media feed capacity by 
500 sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
Downloaded From ManualsPrinter.com Manuals 

Lower Feeder Unit PF-P08 14-4
Installing a Lower Feeder Unit PF-P08 
Note
Since consumables are installed in the machine, be sure to keep the 
printer level when moving it in order to prevent accidental spills.
1Turn off the machine and discon-
nect the power cord and inter-
face cables.
2Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
3Open the right side cover of the 
lower feeder unit.
The right side cover of the lower feeder must be opened before the...

Lower Feeder Unit PF-P0814-5
4With another person’s help, 
place the machine on top of the 
lower feeder unit, making sure 
that the positioning pins on the 
lower feeder unit correctly fit into 
the holes on the bottom of the 
machine.
WARNING!
This machine weighs approximately 39 kg (86 lbs) when it is fully 
loaded with consumables. The machine must be lifted by two people.
5Close the right side cover of the 
lower feeder unit.
6Reconnect all interface cables.
39 kg
86 lbs
Downloaded From...

Working Table WT-P01 14-6
7Reconnect the power cord, and 
turn on the machine.
8Declare Paper Source Unit 3/4 in the Windows printer driver [Properties]/
[Configure] tab.
Working Table WT-P01
Provides an area to temporarily place an original or other materials. This is 
also used when the authentication device is installed.
Kit Contents
a—Working table
b—Mounting plate
Downloaded From ManualsPrinter.com Manuals 

Working Table WT-P0114-7
c—Four screws
d—Two screws
e—Two clamps
Use this part when installing the Authentication Device (IC card type). 
Store the part in a safe place for future use.
Installing a Working Table WT-P01
1Using a coin, turn the screws (c) 
to install the mounting plate.
c
b
Downloaded From ManualsPrinter.com Manuals