Konica Minolta bizhub 40P User Manual

							Finishing 111 Offset Printing
If offset printing is selected, the paper is fed out shifted as shown below.
When PAPER MENU/COLLATE is set to ON, the pages are fed out 
in sets as shown below.
- When 
COLLATE is set to ON- When COLLATE is set to OFF
321321
321
333222
111
Downloaded From ManualsPrinter.com Manuals 
						

							Media Storage 112
Media Storage
How do I store media?
„Keep media on a flat, level surface in its original wrapper until it is time to
load it.
Media that has been stored for a long time out of its packaging may dry up 
too much and cause misfeeding.
„If media has been removed from its wrapper, place it in its original pack-
aging and store in a cool, dark place on a level surface.
„Avoid moisture, excessive humidity, direct sunlight, excessive heat (above 
35°C [95°F]), and dust.
„Avoid leaning media against other objects or placing it in an upright posi-
tion.
Before using stored media, do a trial print to check print quality. 
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing
Consumables
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 114
Replacing Consumables
Before replacing consumables, make sure that the power of the printer is 
turned off.
Note
Failure to follow instructions as outlined in this manual could result in 
voiding your warranty.
Note
If an error message (TONER OUT, FUSER UNIT END OF LIFE, etc.) 
appears, print out the configuration page, and then check the status of the 
consumables. For details on the error messages, refer to “Error Messages 
(Warning:)” on page 182. For details on printing the configuration page, 
refer to “Printing a Configuration Page” on page 150.
About toner cartridge
This printer uses a toner cartridge that includes the toner and the photosensi-
tive drum. If the output image is light or blurred, the toner cartridge may be 
defective or damaged. In that case, you need to replace it with a new one.
Handle the toner cartridge carefully to avoid spilling toner inside the 
printer or on yourself.
Install only a new toner cartridge in your printer. If a used toner car-
tridge is installed, the indicator message will not clear and the supplies 
status in the Status Monitor will not be updated.
The toner is nontoxic. If you get toner on your skin, wash it off with 
cool water and a mild soap. If you get toner on your clothes, lightly 
dust them off as best as you can. If some toner remains on your 
clothes, use cool, not hot water, to rinse the toner off.
CAUTION
If you get toner in your eyes, wash it out immediately with cool water 
and consult a doctor. 
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 115
Note
Do not use refilled toner cartridges or unapproved toner cartridges. Any 
damage to the printer or quality problems caused by a refilled toner 
cartridge or an unapproved toner cartridge will void your warranty. No 
technical support is provided to recover from these problems.
When replacing a toner cartridge, refer to the following table. For optimum 
print quality and performance, use only approved KONICA MINOLTA toner 
cartridge for your specific printer type, as listed in the table below. You can 
find your printer type and the toner cartridge part numbers on the consum-
ables reorder label inside the front cover your printer.
For optimum print quality and performance, use only the corre-
sponded TYPE genuine KONICA MINOLTA toner cartridge.
Keep toner cartridges: 
„In their packaging until you’re ready to install them.
„In a cool, dry location away from sunlight (due to heat). 
The maximum storage temperature is 35°C (95°F) and the maximum 
storage humidity is 85% (noncondensing). If the toner cartridge is moved 
from a cold place to a warm, humid place, condensation may occur, 
degrading print quality. Allow the toner to adapt to the environment for 
about one hour before use.
„Level during handling and storage. 
Do not hold, stand or store a cartridge on its ends or turn it upside down; 
the toner inside the cartridge may become caked or unequally distributed.
„Away from salty air and corrosive gases such as aerosols.
Printer 
Ty p ePrinter Parts 
NumberToner Cartridge Type Toner Cartridge 
Parts Number
AM A0DX 013 High-Capacity Toner Cartridge - Black (K) A0FP 013
EU A0DX 023 High-Capacity Toner Cartridge - Black (K) A0FP 023
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 116
Replacing a Toner Cartridge
Note
Be careful not to spill toner while replacing a toner cartridge. If toner 
spills, immediately wipe it off with a soft, dry cloth.
If 
TONER LOW on the SYS DEFAULT MENU/ENABLE WARNING is set 
to 
ON, the message TONER LOW appears when the toner cartridge becomes 
near empty. Follow the steps below to replace the toner cartridge.
If TONER LOW on the SYS DEFAULT MENU/ENABLE WARNING 
is set to 
OFF, you are advised to replace the toner cartridge when the 
message 
TONER OUT appears.
1Open the top cover.
2Hold the toner cartridge by the 
grip, and then pull it out slowly.
3Take the new toner cartridge out of the box.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 117
4Holding it firmly with both hands, 
rock the toner cartridge left and 
right, forward and backward, to 
distribute the toner evenly.
Do not touch the devel-
oping roller of the toner 
cartridge; otherwise 
image quality may 
decrease.
5Placing the toner cartridge on a 
flat surface, pull out the seal hor-
izontally.
6Hold the toner cartridge by the 
grip, and then insert it into the 
slot inside the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 118
7Close the top cover securely.
Note
Dispose of the used toner cartridge according to your local regulations. 
Do not burn the toner cartridge.
For details, refer to “About toner cartridge” on page 114.
Replacing the Fuser Unit
When it is time to replace the fuser unit, the message FUSER UNIT END 
OF LIFE
 appears. Printing can continue even after this message appears; 
however, since the print quality is reduced, the fuser unit should be replaced 
immediately.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 119
1Turn off the printer and discon-
nect the power cord.
There are extremely hot 
parts within the machine. 
Before replacing the 
fuser unit, wait about 30 
minutes after turning off 
the machine, and then 
check that the fusing sec-
tion has reached room 
temperature; otherwise, 
you may get burnt.
2Lift the lever shown in the figure.
3Open the rear cover.
Do not touch any parts 
inside the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing Consumables 120
4Pull down the 2 levers at the bot-
tom of the fuser unit.
5Remove the fuser unit slowly.
Downloaded From ManualsPrinter.com Manuals