Home
>
Key System U.S.
>
Communications System
>
Key System U.S. Atlas Avm Jr Installation Programming Instruction Manual
Key System U.S. Atlas Avm Jr Installation Programming Instruction Manual
Here you can view all the pages of manual Key System U.S. Atlas Avm Jr Installation Programming Instruction Manual. The Key System U.S. manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 51
DTMF Programming Atlas AVM JR. Installation and Programming Manual 3-27 For instructions on programming the above script messages, see Section 3.7.2. For instructions on recording the script messages, see Section 3.7.1. 3.7.5.4 Do Not Disturb Using the user menu, a mailbox owner can activate the Do Not Disturb mode. When a caller dials a Do Not Disturb extension, the AVM JR. plays system message 121 and does not transfer the call to the extension. The System Administrator can replace this...
Page 52
DTMF Programming 3-28 Atlas AVM JR. Installation and Programming Manual 3.8.1.2 Changing the Operator’s Password The System Administrator can change the operator’s password by dialing code *900 to enter the programming mode, dialing the System Administrator’s password and then dialing: *601 + XXXX Where XXXX is the new 4-digit password. Use digits 0-9 only. Do not dial * and #. To disable the operator’s password, enter “0000”. 3.8.1.3 Resetting the Mailbox Password The System Administrator...
Page 53
DTMF Programming Atlas AVM JR. Installation and Programming Manual 3-29 This password can be disabled. See Section 3.8.1.2. Y = 0; Reduce the time by one hour Y = 1; Increase the time by one hour 3.8.4 Changing the Operational Mode The operator can change the operational mode by calling the AVM JR. and, during the opening greeting, dialing: *8 + XXXX + Y Where: XXXX refers to the operator’s password. This password can be disabled. See Section 3.8.1.2. Y = 0; Day Mode Y = 1; Night Mode Y =...
Page 54
DTMF Programming 3-30 Atlas AVM JR. Installation and Programming Manual 3.8.8 Resetting the System The System Administrator can reset the AVM JR. to its factory default settings by dialing: *654 + * + XXXX + # Where XXX is the System Administrator’s password. 3.8.9 Adjusting Recording Length The System Administrator can select the length of the recorded messages in the AVM JR. The selected length of message (in minutes) will effect all recorded messages. The types of recorded messages...
Page 55
Atlas AVM JR. Installation and Programming Manual 4-1 4. PROGRAMMING BY COMPUTER This section describes how to program the AVM JR. using the Voicemail Utility Program (VUP). You can work with the VUP online or off-line. The VUP enables you to: · Define PBX parameters · Set the AVM JR. clock and calendar · Create and maintain mailboxes · Build Automated Attendant menus · Review traffic statistics · Print system parameters and statistics All changes to the AVM JR.’s configuration are...
Page 56
Programming by Computer 4-2 Atlas AVM JR. Installation and Programming Manual 2. Connect one end of the RS-232 cable to one of the unused serial ports of your PC and the other end to the AVM JR.’s RS-232 connector as shown in Figure 4-1. Figure 4-1 RS-232 Cable Connection 4.2 4.2 System Requirements System Requirements Before installing the VUP, check that your computer meets the following minimum requirements: · PC 486 or higher · 8 MB RAM · 2 MB free hard disk space · Microsoft...
Page 57
Programming by Computer Atlas AVM JR. Installation and Programming Manual 4-3 4.3 4.3 Installing the VUP Installing the VUP ä To install the VUP: 1. Exit all open applications. 2. Insert the VUP installation diskette into the floppy drive on your computer. 3. Use File Manager or Windows Explorer to locate the setup file. Or with Windows 95/98 you may click on start, select run and type in X:\SETUP.EXE where X equals the drive letter 4. Double-click the setup file. 5. Follow the...
Page 58
Programming by Computer 4-4 Atlas AVM JR. Installation and Programming Manual The VUP loads the data stored in the default configuration file and opens the main screen. Figure 4-2 VUP Main Screen ä To select a COM port: 1. On the Communication menu, click Com Port. The Communication Port dialog box opens. 2. Click the appropriate COM port (1-4) according to your computer’s configuration. Then select Ok to enable the COM port.
Page 59
Programming by Computer Atlas AVM JR. Installation and Programming Manual 4-5 Note: If you are unsure of your COM port and you are using a portable/laptop computer try selecting COM 1, as this is usually the default setting on most of these types of systems. ä To load the data stored in the AVM JR. database: · On the Communication menu, click Read Parameters. The VUP reads the AVM JR. database and overwrites the current settings. ä To load data stored in a configuration file: 1. On the File...
Page 60
Programming by Computer 4-6 Atlas AVM JR. Installation and Programming Manual ä To define the PBX parameters: On the Parameters menu, click PBX Parameters. The PBX Parameters dialog box opens. Figure 4-3 PBX Parameters Extension Screen The PBX Parameters are divided into four sections; Extensions, Call Transfer, Supervision and CP Tone & Disconnect. 4.5.1.1 Defining Extension Parameters On the extension screen there are six fields that should be filled in. · Extension Size – This is the...
All Key System U.S. manuals