Inter-Tel Imx/Gmx 416/832 Installation Manual

JNTER-TELdPRACTICES 
IMX/GMX 416/832 INSTALLATION & WANCE INSTALLATION 
Issue 1, November 1994 
NOTE: When testing a 12-line keyset, a 
hookflash must be performed for each 
missing station programmable key 
(13-24). To do this, lift and replace the 
handset each time a missing key (13-24) 
istobepressed. 
2. Feature keys in this order: REDIAL, SYS 
SPD, ANSWER, OUTGOING, SPKR, 
CNF, MUTE, FWD, DAlX, DND, IC, 
MSG, HOLD, XFR, PAGE, QUE, MU- 
SIC, and SPCL. 
3. Keypad keys in the following order: l-9, 
l...

INSTALLATION Issue 1, November 1994 INTER-TELPRACTICES IMX/GMX 416/832 INSTALIATION & MAINTRNANCE 
the handset receiver via the secondary voice 
path. (Display shows KTS SELFTESTHOT 
HANDSET SEC.) 
p. While speaking into the handset transmitter, 
determine that sidetone is being received 
over the handset receiver. 
q. Press and release the hookswitch. The speak- 
erphone microphone is connected to the 
handset receiver. (Display shows KTS 
SELF-TEST SPKRPHONE MIC.) 
r. While speaking into the...

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE INSTALLATION 
Issue 1, November 1994 
FIGURE 3-67. BOTTOM OF &LINE DUALXIRCUIT IMX AIM KEYSET 
CIRCUIT SELECTION 
SWITCH 
I 
0 8 
0 Q ::::::::::::::::::::~::~~~::::~.:~.:.:.:: 
..:.:.: . . 
.ii,. . . . . . . . :.:.: . . . . . . . . < .,.,.,.,. :A:.:.:.:,: 
,..............., . . . . . . . . . . . . . . . . :..... .:.:, 
:::::::::::::::::~:~:~:~:~:::~:~:;:~:~:f::::~: :,:,: 
Q 
Page 3-119  

INSTALLATION 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION 8z MAINTENANCE 
Wall Mounting IMX 24/12/8&ine Keysets 
7.17 
(1) 
(2) 
(3) 
(4) 
(5) 
(6) 
Q 
To mount the keyset on a wall: 
Remove the keyset baseplate by removing the 
retaining screw, pressing on the bottom edge 
(1Zline and 24line keysets) or the top edge 
(g-line keysets) of the baseplate to release the 
tab, and pulling the plate off. 
NOTE: To facilitate easy removal of the base- 
plate, the 
retaining screw on...

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALL4TION & MAINTENANCE INSTALLATION 
Issue 1, November 1994 
Optional Data Port Module 
7.21 All IMX 
12-line and 24-line keysets may be 
equipped with optional Data Port Modules (refer to RE- 
PLACEMENT PARTS for the part number). The Data 
Port Module contains a four-conductor modular jack 
that can be used 
to comtect eirher a data device (such as a 
personal computer with a directconnect modem) or an 
LRA and an external signaling device (such as a loud 
bell,...

INSTALLATION 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
FIGURE 3-68. IMX KEYSET DATA PORT MODULE INSTALLATION 
STRAPS 
MODULAF 
JACK 
DATA POR 
MODULE 
SHORTING 
PLUG 
LOCATIO! 
.:.:.:.:.:.:.:.:.:.:.:.~.:.:.:.:.:.:.q:.:$~: 
::::::::::::!:::~~~~~~::~:::: 
8 
/ /- .~~:~:::::::~:~:::::~.::::::::::::::: 
 Q 
/ 
/  
SETTING FOR 
DATA DEVICE 
4 
:! 
i 
/’ 
Page 3-122  

INTER-TJZLPRACTICES 
IIWVGMX 416/832 @WlXLLATION % -ANCE INSTALLATION 
Issue 1. November 1994 
7.26 To connect a Loud Ringing Adapter (LRA): 
The optional Data Port Module can be used to connect 
external signaling equipment such as loud bells, horns, 
flashing lights, etc. to a keyset. This application is useful 
in areas where the normal ring tone of the keyset cannot 
be heard, such as warehouses and loading docks. The 
signaling device follows the normal ringing patterns of 
the keyset. 
NOTE: Since...

lBWlMLA’l’lON 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
C. GMX416/832 ANALOG KEYSET 
lNS’lALIATION 
7.29 Before installing keysets, unpack each one and 
check for damage. lf items are damaged or missing, con- 
tact Customer Support. Each keyset should have the fol- 
lowing: 
Baseplate 
Extra key caps 
One six-foot, three-pair line cord 
One handset 
One four-conductor coiled handset cord 
Slide-out directory card 
Optional Liquid Crystal Displays (LCDs) 
730...

lNTER-TEL4PRAcTIcES 
lMX/GMX 416/832 INSTALLATION & M&NlENANCE INSTALLATION 
Issue 1, November 1994 
FIGURE 3-70. INTER-TEIJDVK 24-LINE KEYSET “LARGE” LCD INSTALLATION 
KEYSET HOUSING (INSIDE VIEW) 
_ DISPLAY 
WINDOW 
LCD 
- CONNECTOR 
_ RIBBON 
CABLE 
- LCDUNlT 
_ CONTROL 
BOARD 
Page 3-125  

INSTALLATION Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
7.32 Inter-Tel/DVK 12.Line and S-Line Keysets: 
To convert a standard Inter-Tel/DVK 1Zline or 84ine 
keyset to a display keyset, install the small LCD Kit 
(part no. 828.1165) as outlined in the following steps: 
(1) 
(2) 
(3) 
(4 
(5) 
(6) 
(8) 
Unpack the LCD kit. There should be a clear 
plastic display window, an LCD unit, a ribbon 
cable, and two small Phillips-head screws. 
Remove the keyset...