Inter-Tel Imx/Gmx 416/832 Installation Manual

INTER-TELPRACTICES 
IMX/GM.X 416/832 INSlXLLATION & MAINTENANCE INSTAJLATION 
Issue 1, November 1994 
FIGURE 3-57. LOOP/GROUND START CARD OLGC) 
LED INDICATORS 
6 
< 
AMPHENOL-TYPE . 
CONNECTOR 
THESE NUMBERS 
ARE SILKSCREENED 
ON THE CARD 
: 
. ..$ 
P :.:::. 
. . . . . . . 
* 
2 STRAPS STRAPS FOR 
- ClFiCUlT3 
1 STRAPS FOR 
- CIRCUIT2 
0 STFIAPS FOR 
- CIRCUIT1 
7 STRAPS FOR 
- ClRCUiT8 
6 STFWS FOR 
- CIRCUIT7 
5 - STRAPSFOR 
CIRCUIT 6 
2 STRAPSFOR 
Q CIRCUIT 5 
FUSES 
Page 3-97  

INS’E4LLATION 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION % MAINTENANCE 
FIGURE 3-58. LOOP START CARD (LSC) 
LED INDICATORS 
AMPHENOL-TYPE 
l 
CONNECTOR 
CARD ACTIVE (GREEN) 
FUSES 
Page 3-98  

INTER-TELPRACTICES 
IMWGMX 416/832 INSTALLATION & MAINTENANCE INSTALLATION 
Issue 1, November 1994 
E&M Cards (EM&) 
6.50 
Install each EMC as described below (see RE- 
PLACEMENT PARTS for the part number). Refer to 
Figure 3-59 on page 3-100 for an illustration. 
NOTE: When inserting or removing the Matrix Card, 
Expansion Card, and/or the computer cards, the system 
power must be turned off to prevent damage to the cards. 
However, station and trunk cards can be inserted or re- 
moved with power on....

INSTALLATION 
Issue 1, November 1994 
IMx/GMx 
416/832 IN~~xLL?=-= pRAcTIcEs TNm & -ANCE 
FIGURE 3-59. 
E&M CARD (EMC) 
 
2 
j 
LED INDICATORS 
< 
AMPHENOL-TyPE 
CONNECTOR - 
MAKE-BUSY 
SWITCH - 
(RESERVED FOR 
FUTURE USE) 
SIGNALING TYPE 
SELECTION JUMPERS 
FUSES THESE 
NUMBERS 
ARE SILKSCREENED 
ON THE CARD 
1 J 
- JUMPERS FOR 
CIRCUtT 2 
0 - JUMPERSF 
ClRCLm ‘OR 
1 
3 - JUMPERS FOR 
CIRCUIT 4 
2 - JUMPERS FOR 
CIRCUIT 3 
AUDI6 TYPE 
SELECTION JUMP- 
ERS 
Page 3-100  

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE INSTALLATION Issue 1. November 1994 
(1) If installing the optional on-board Channel Ser- 
vice Unit (CSU), follow these steps: 
I 
a. NOTE: The on-board CSU can now be pur- 
chased directly from Inter-Tel using part 
number 440.3004. 
Carefully plug the CSU into the large socket 
provided on the card (see Figure 3-60). 
b. Place the DSX/CSU jumper plug in the CSU 
(518) position. 
C. Depending on the distance to the nearest pub- 
lic network...

INSTALLATION 
Issue 1, November 1994 INTER-TELPRACTICES 
IMYUGMX 416/832 INSTALIATION & MAINTENANCE 
FIGURE 3-60. TlC CARD (Tic) 
LED INDICATORS 
PROVIDING REF- 
ERENcEcLDcK 
ALARM RELAY JACK - 
SERIAL PORT JACK- 
NOT CURRENTLY USED 
Tl SPAN JACK - 
BANTAM TEST JACKS * 
Tl SPAN DB15 _ 
CONNECTOR DSWCSU 
SELECTION JUMPER 
SELECTION JUMPER 
Page 3-102  

INTER-TELPRACTICES IMJUGMX 416/832 INSTALLATION % MAINTENANCE 
INSTALLATlON 
Issue 1, November 1994 
J. CHECK TEIE TELECOMMUNICATION 
CIRCUIT CARD INSTALLATION 
6.52 After all of the circuit cards have been installed 
in both the main equipment cabinet and the expansion 
cabinet, check the installation by performing the fol- 
lowing steps. 
NOTE: If, on expanded systems, the expanded system 
software is not already installed on the hard disk drive, 
the LEDs on the cards in the expansion cabinet will not...

INS-TION Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
K. COMPLETE TEIE EQUIPMENT CABINET 
INSTALLATION 
6.53 Complete the equipment cabinet installation as 
follows: 
(1) 
If any of the telecommunication cables (includ- 
ing any line cona3 or ribbon cables used 
for Tl) 
are being dmlpped ftvm the ceiling, rather than 
being routed up from the floor, install the two 
cable brackets (included with the system) on the 
back of the main equipment cabinet. The cable...

INTER-TELPRACTICES 
IMX/GMX 416/832 INSMLLATION & MAINTENANCE INS’IALLATION 
Issue 1, November 1994 
7. SlATION INSIALLATION 
I 
7.1 Digital keysets are connected to Digital Keyset 
Cards. Analog keysets, analog DSWBLF Units, and At- 
tendant Computer Consoles are connected to Keyset 
Cards. ESLSs, SLJs, single-line M’MF sets, and play- 
back devices are comtected to Single-Line Cards and/or 
Jnward Dialing Cards. 
41 Connectmg a statton mstrument to the wrong type 
NOTE: For information on installing...

INS-TION INTER-TELPRACTICES 
Issue 1. November 1994 lMX/GMX 416/832 INS’IALLATION & 
MAINTENANCE 
fully seated and properly aligned in the con- of the faceplate housing is still fully seated and 
nectar. properly aligned. 
(9) Reconnect the line (J2), microphone (J4), hand- (11) Reattach the back of the keyset. 
set (J5), speaker (J6), and, if equipped, data port 
(53) wires to the keyset control board. (12) To ensure that the LCD unit and keyset control 
board are properly come&d and functioning, 
(10)...