Inter-Tel Imx/Gmx 416/832 Installation Manual

lNTER-TJcLlPRACTIcEs IMX/GMX 416/832 INSTALLATION & MAINTENANCE INSTALLATION 
Issue 1, November 1994 
FIGURE 3-35. 
CABLE CONNECTOR PINOUTS AND VOLTAGE 
TEST POINT LOCAnONS 
FRONT SIDE OF POWER SUPPLY CHASSIS 
I I  I 
I  I 
, ‘. DISK DRIVE POWER CABLE 
 (Same for both cables) 
PC MOTHERBOARD /  PCMOTHERBOARD /’ 
POWER CABLE .  POWER CABLE . 
   /  / 
.  . 
/  / 
,  , 
I  I 
   
.  . 
.  . 
‘  ‘ 
WIRE FROM 
HDLC CARD 0 
0 
0 
0 
0 
0 
0 
0 
0 
0 
0 
0 HDLC POWER CABLE 
cl PWR GOOD 
cl PWR ALARM 
cl 1 PWR...

INSTALLATION 
Issue 1, November 1994 INTER-TELPRACTICES 
IMWGMX 416/832 INSTALLATION % MAINTENANCE 
FIGURE 3-36. MAIN POWER SUPPLY CONNECI’OR PINOUTS AND -_ 
. 
VOLTAGE TEST POINT LOCATIONS .: 
., 
4 
CHASSIS GND 
POWER ALAFIM 
POWER GOOD 
CONNECTOR 
TO HDLC 
(Via the HDLC 
Power Cable) 
/ FRONT SIDE OF MAIN POWER SUPPLY CHASSIS 
VRING 
PWRAIAFIM 
BGND 
CONNECTOR TO 
DRIVES & OPT. COOLING FA 
(Via the Disk Drive 
Power Cables) 
GND 
+!N 
+12v 
NO CONNECTION 
-12v 
GND 
CONNECTORS 
TOPCMOTHERBOARD 
(Via...

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE INSTALLATION 
Issue 1, November 1994 
FIGURE 3-37. EXPANSION POWER SUPPLY CONNECI’OR PINOUTS AND 
VOLTAGE TEST POINT LOCATIONS 
VRING 
POWER AIARM 
BOND 
CONNECTOR TO 
MAIN POWER SUPPLY 
(Via the V-Ring 
Power Cable) FRONT SIDE OF EXPANSION POWER SUPPLY CHASSIS 
VRING 
BGND 
BGND 
-48V 
-4W 
DGND +5V 
+5V SENSE 
DGND 
+!%I SEN FITN DGND 
+SVANLG +5V 
+SVANLG KGND 
KGND 
KGND 
+3ov 
+3ov 
+3Qv 
CPCN -12V 
CPCP 
+12v 
+12v PWRALM 
-5vANLG 
AGND...

INSliULA’l’lON 
Issue 1, November 1994 INTER-TELPRACTICES 
IhWGMX 416/832 INSTALLATION & MAINTENANCE 
F. INSlXLLTEECOMPUTERCARDS 
NOTICE 
Personal computer (PC) technology is continually 
evolving. As it does, the 416/832 System will con- 
tinue to incorporate important design enhance- 
ments. Thus, depending on the actual version of 
equipment that is shipped, the following installa- 
tion instructions could vary somewhat. If revised 
instructions are included with the equipment, refer 
to them instead....

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE INSTALLATION 
Issue 1, November 1994 
FIGURE 3-38. 
PCC PC MOTHERBOARD 
MOUNTING 
LOCATIONS 6 
5-PIN DIN CONNECT 
TO PROGRAMMING KEYBOARD 
12-PIN CONNECTOR 
TO POWER SUPPLY 
HDLC CARD 
CONNECTOR 
MONITOR CARD 
CONNECTOR 
PRO68lPRO68E CARD 
CONNECTOR 
NOT CURRENTLY USED 
NOT CURRENTLY USED 
< MODEM CARD 
CONNECTOR 
NOT CURRENTLY USED 
DISK CONTROLLER 
CARD CONNECTOR 
Page 3-61  

INSTALLATION Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 nWlALLATION & MAINTENANCE 
PC Motherboard - SUNTAC Version 
6.21 
Install the “SUNTAC” version PC Motherboard 
as outlined in the following steps. For a drawing of the 
card, refer to Figure 3-39 on page 3-63. 
NOTE: The SUNTAC PC Motherboard cannot be used 
with the new IDE-type Disk Controller Card. 
(1) 
(2) 
(3) 
(4 
Ensure the AC POWER switch is turned OFF. 
NOTE: When inserting or removing the com- 
puter cards, the system...

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE IN!tXALLATION 
Issue 1, November 1994 
FIGURE 3-39. SUNTAC PC MOTHERBOARD 
MOUNTING DIP SWlTCHE 
12-PIN CONNECTOR 
TO POWER SUPPLY 
S-PIN DIN CONNECTOR 
TO PROGRAMMING KEYSOARD 
HDLC CARD 
CONNECTOR 
MONITOR CARD 
CONNECTOR 
PR068/PR068E CARD 
1 CONNECTOR 
- NOT CURRENTLY USED 
- NOT CURRENTLY USED 
 MODEM CARD 
CONNECTOR 
’ NOT CURRENTLY USED 
1 DISK CONTROLLER 
CARD CONNECTOR 
Page 3-63  

INS-TION 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALL4TION % MAINTENANCE 
PC Motherboard - VLSI Version 
6.22 Install the “VLSI” version PC Motherboard as 
outlined in the following steps. For a drawing of the 
card, refer to Figure 3-40 on page 3-65. 
NOTE: The VLSI -PC Motherboard can only be used 
with HDLC Cards that have been modified and labeled 
I with ECN-2279 or stamped with artwork number 
826.3806-1, -2, or higher. 
(1) Ensure that the AC POWER switch is turned 
OFF....

INTER-TELPRACTICES IMX/GMX 416/832 lNS’MLLATION & MAINTENANCE INSTALLATION 
Issue 1. November 1994 
FIGURE 3-40. VLSI PC MOTHERBOARD 
STRAP 
LOCATIONS 
12-PIN CONNECTOR 
TO POWER SUPPLY 
HDLC CARD 
/ CONNECTOR 
MONlTOR CARD 
/ CONNECTOR 
068/PR068E CARD 
CONNECTOR 
MODEM CARD 
CONNECTOR 
NOT CURRENTLY USED 
DISK CONTROLLER 
CARD CONNECTOR 
NOT CURRENTLY USED 
NOT CURRENTLY USED 
5PIN DIN CONNECTOR 
TO PROGRAMMING KEYBOARD 
Page 3-65  

INSTALLATION 
Issue 1, November 1994 INTER-TELPRACTICRS 
IMX/GMX 416/832 INS’IALJATION & MAJNTENANCE 
PC Motherboard - MXIC Version 
6.23 Install the MXIC PC Motherboard as outlined in 
the following steps. For a drawing of the board, refer to 
Figure 3-41 on page 3-67. 
NOTE: The MXIC PC Motherboard can only be used 
with HDLC Cards that have been modified and labeled 
with ECN-2279 or stamped with artwork number 
826.3806-1, -2, or higher. 
(1) 
(2) 
(3) 
(4 
(5) Ensure that the system AC POWER is...