Inter-Tel Imx/Gmx 416/832 Installation Manual

BTER-TELPRACTICES 
IMX/GMX 416/832 INSUTION & MAINTENANCE INSTALLATION Issue 1, November 1994 
FIGURE 3-8. EMC BLOCK CABLE TERMINATIONS 
E&M 
CARD EMC 
- 
AMPHENOL- 
TYPE 
CONNECTOR 
/ 
- 
- 
- 
- 
66Ml-50-TYPE 
BLOCK 
(PART OF MDF) TO 
b TELCO 
RJ 
TO 
TELCO 
RJ 
NOTE: Depending on the area of the country and/or the specific type of E&M trunk ordered, one or more of 
the cable pairs shown above may not always be needed. For each E&M trunk to be installed, terminate all 
cable pairs provided by the...

INSEiLI.ATION Issue 1, November 1994 INTER-TELPBACTICES 
IMX/GMX 416h332 INSTALIATION & MAINTENANCE 
B. CONNECTING Tl SPANS TO TEE MDF 
5.8 The installation procedure used to connect Tl 
spans at the MDF is dependent on the type of termina- 
tion used by the telephone company and how close it is 
to the MDF. The Tl spans may be terminated on RJ48C 
modular jacks or on RJ-type terminal blocks. 
5.9 Follow one of the three Tl termination methods 
(A, B, or C) outlined on the following pages. 
NOTE: The Tl...

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE INSTACLATION 
Issue 1, November 1994 
FIGURE 3-9. 
Tl SPAN TERMINATIONS FROM RJ48C JACKS 
FOUR-PAIR, NON- 
REVERSING, 
MOD-TO-MOD FOUR-PAIR, NON- 
REVERSING, 
MOD-TO-MOD 
LINE CORD Tl CABLE LINE C :ORD 
fr 
TO II -I: 
TELCO ‘b= /\--ir$ TO 
R~= ~ ” Ti CARD 
JACK EIGHT-CONDUCTOR 
MODULAR JACK ASSEMBLIES 
FIGURE 3-10. MODULAR JACK ASSEMBLY WIRING FOR Tl SPANS 
MODULAR JACK ASSEMBLY 
RING 
WT TIP1 
WI RING 1 
(IN 
FOUR-PAIR, NON- 
REVERSING,...

INSTALLATION 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALIATION & MAINTENANCE 
Method C 
- Tl Spans Terminated On An 
RJ-Qpe Block 
5.12 Install Tl spans terminated on an RJ-type block 
as outlined in the following steps. Refer to Figure 3-11 
below for a diagram of the complete layout. cable for transmit and one cable for receive) may 
be used instead. 
a. Terminate one end of a six-pair cable on each 
modular jack assembly. Refer to Figure 3-10 
on the previous page. 
(1) On the...

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE INSTALLATION 
Issue 1, November 1994 
Using The Optional DB15 Connector In Place Of 
The BJ48C Jack 
5.13 
The three Tl installation methods described on 
the preceding pages show the Tl span being connected 
to the RJ4gC jack on the Tl Card. However, in certain 
situations (e.g., when using an external CSU equipped 
with a DB15 connector), the installer may wish to use 
the card’s optional DB15 connector instead. 
5.14 The pin functions of...

INS’lALLATION 
Issue 1, November 1994 INTER-TELPRACTICES IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
C. COlWECTING S+lXIlON CABLES TO TEIE 
MDF 
5.16 Each type of station instrument is connected to a 
I specific station card. Digital keysets are connected to 
DKSCs. Analog keysets, analog DSS/BLF Units, and 
Attendant Computer Consoles are connected to KSCs or 
KSC-Ds. Single-line sets and playback devices are con- 
nected to SLCs and/or IDCs. 
NOTE: Resides single-line sets, playback devices, and...

INTER-TELPRACTICES INSTALLATION IMX/GMX 416/832 INS’lALLATION % MAINTENANCE Issue 1, November 1994 
FIGURE 3-13. DIGITAL KSC BLOCK CABLE TERMINATIONS FOR KEYSETS 
L 
DIGITAL 
KEYSEl 
CARD DKSC 
np 
RING - 
-- 
np - 1.211 _ _ x1.21- - - - 
RIMG - 
AMPHENOL- 
TYPE 
CONNECTOR 
66hW50-TYPE 
BLOCK 
(PART OF MDF) 
np 
MODULAR 
JACK 
ASSEMBLY 
G Y 
R 
R BK 
1 I , 
I 
RING 
I 
TO DIGITAL 
KEY.93 
TO DIGITAL 
KEYSET 
NOTE: For simplicity, this figure shows keysets being installed using one-pair cable and...

INSTALLATlON 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 lNSTAL,LA~ON & MAINTENANCE 
FIGURE 3-14. ANALOG KSC BLOCK CABLE TERMINATIONS 
KSC 
TO KEYSET, 
AllENDANT 
CONSOLE, 
OR DSS/BLF 
KEYSET 
CARD 
r 
I 1 WDPFiI 
I 
WD SEC 
MODULAR 
TO KEYSET, 
AllENDANT 
CONSOLE, 
OR DSSBLF 
AMPHENOL- 
TYPE 
CONNECTOR 
66Ml-50-TYPE  66Ml-50-TYPE 
BLOCK  BLOCK 
(PART OF MDF)  (PART OF MDF) 
Page 3-24  

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE INSTALLATION 
Issue 1, November 1994 
FIGURE 3-15. INSTALLING &LINE IMX AIM KEYSETS TWO TO A CIRCUIT 
CIRCUIT l.lA 
MDF 
KSC-D - 
CIRCUIT l.lB 
A 
CIRCUIT 1 .lA 
B 
C 
MDF 
BLOCK 
KSC-D -- 
 
CIRCUIT l.lB 
CIRCUIT 1 .I A 
MDF 
KSC-D YE/ 
I I  CIRCUIT l.lB 
NOTE This illustration shows three common methods for installing two 8-line IMX AIM keysets on a single 
KSC-D circuit. For a detailed wiring diagram of method A, refer to the following...

INSTALLATION Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
FIGURE 3-16. KSC-D BLOCK CABLE TERMINATIONS FOR &LINE IMX AIM 7 
KEYSETS INSTALLED TWO TO A CIRCUIT g 
1” 
1.1 
1.2 L- 1 1.1 I 
1- 1 1 
1-I - 
I- I - 
- 
1- 1 - 
I- 1 - 
1.2 
---- 
66Ml-W-TYPE 
BLOCK 
(PART OF MDF) L 1 
BIJWGH) MODULAR 
JACK 
ASSEMBLY 
CIRCUIT 1 .l A 
TO &LINE 
AIM KEYSET 
MODULAR 
JACK 
BLlwoND ASSEMBLY 
ON PFII 
GM SEC 1 CIRCUIT 1 .I B 
I I 
f 
TO SLINE 
AIM KEYSET 
NOTE: This...