Inter-Tel GMX-48 INSTALLATION & MAINTENANCE Manual

PROGRAMMING 
Issue 2, May 1990 ‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
H. [AH] PASSWORDS (/PASS) 
4.18 The 
database programming, SMDR and error 
programming, &AR/call cost programming, and on- 
line monitor menus each can be assigned passwords 
that limit access. 
4.19 The database programming menu can have up 
to three passwords; each specifies a different level of 
access: 
Database inspection level allows any portion of 
the database to be viewed, except the save/re- 
store,...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE ‘,. 
PROGRAMMING 
Issue 2, May 1990 
CHANGE UNRESTRICTED PASSWORD (N)? N- Advance to the SMDR password prompts: 
Y- Continue to the next prompt. 
ENTER NEW PASSWORD: Enter up to eight characters. 
ENTER NEW PASSWORD AGAIN: Repeat the same characters. If the two entries do 
not match, an error message appears; return to the 
ENTER NEW PASSWORD prompt. 
PERFORM UPDATE TO SYSTEM DATABASE 
ci ORN) 
REQUIRE A PASSWORD FOR SMDR AND 
ERROR (N): 
CHANGE SMDR...

PROGRAMMING 
Issue 2, May 1990 ‘.. 
INTER-TEL PRACTICES 
GMX4 INSTALLATION & MAINTENANCE 
REQUIRE A PASSWORD FOR ON-LINE 
MONITOR (N): 
CHANGE ON-LINE MONITOR PASSWORD 
(N)? N- Advance to the REQUIRE A PASSWORD 
FOR NETWORK SELF TEST prompt. 
Y- Continue to the next prompt. 
N- Advance to the REQUIRE A PASSWORD 
FOR NETWORK SELF TEST prompt. 
Y- Continue to the next prompt. 
ENTER NEW PASSWORD: Enter up to eight characters. 
ENTER NEW PASSWORD AGAIN: Repeat the same characters. If the two entries do 
not...

INTER-TEL PRACTICES PROGRAMMING 
GMX-48 INSTALLATION & MAINTENANCE Issue 2, May 1990 
5. [B] EXTENSIONS (INTERCOM 
NUMBERS) AND FEATURE 
ACCESS CODES (/CODE) 
5.1 To reprogram intercom numbers or feature 
codes, enter B or /CODE from the database pro- 
gramming menu prompt. Prompts are shown below 
only for a few extension (intercom) numbers and fea- 
ture codes. To prepare for programming, make a list 
of feature codes, intercom numbers, and pilot num- 
bers and check to be sure they do not overlap. The...

PROGRAMMING 
Issue 2, May 1990 ‘.. 
INTER-TEL PRACTICES 
GMX.48 INSTALLATION 8z MAINTENANCE 
REVIEW ADDITIONAL HUNT GROUPS (N)? 
RANGE OF VOICE COMPUTER GROUPS TO 
BE REVIEWED (NONE): 
VOICE COMPUTER GROUP 6 (E236): 
. . . 
VOICE COMPUTER GROUP 20 (E250): 
REVIEW SAME VOICE COMPUTER GROUPS Y- Return to the fist voice computer hunt group 
AGAIN (N)? in the selected range. 
N- Continue to the next prompt. 
REVIEW ADDITIONAL VOICE COMPUTER 
GROUPS (N)? 
REVIEW FEATURES (N)? 
REVIEW CO LINE ACCESS FEATURE...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE ‘,. 
PROGRAMMING 
Issue 2, May 1990 
FEATURE: NIGHT RING ON/OFF @lo): 
. . . 
FEATURE: PROGRAM LINES IN SERVICE 
(E031) 
REVIEW FEATURES AGAIN (N)? Enter a l-3 digit code for each feature or NONE if 
the feature will not be used. Be careful not to use 
numbers that you have used as intercom numbers 
or feature codes. 
Y- Return to the CO LINE ACCESS prompt. 
N- Continue to the next prompt. 
REVIEW EXTENSION ASSIGNMENTS AGAIN 
(N)? Y- Return to the...

PROGRAMMING 
Issue 2, May 1990 ‘.. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
6. [C] C.O. LINES 
6.1 The programs reached through menu [C] C.O. 
Lines (selection C from the database programming 
menu) establish equipped C.O. lines, C.O. line 
groups, outgoing-access lists, allowed-answer lists, 
and ring-in lists. 
6.2 The menu appears as shown below: 
[C] CO LINES 
[A] CO LINE EQUIPMENT STATUS 
[B] CO LINE GROUPS 
[C] SPECIFIC CO LINE INFORMATION 
[D] AUTO AND LINE KEY ASSIGNMENTS 
[E]...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE ‘.. 
PROGRAMMING 
Issue 2, May 1990 
LIST OF EQUIPPED CO LINES (ALL): 
LIST OF DAY DISA CO LINES (NONE): 
LIST OF NIGHT DISA CO LINES (NONE): 
LIST OF INCOMING-ONLY CO LINES 
(NONE): 
LIST OF OUTGOING-ONLY 
(NONE): CO LINES 
LIST OF PULSE-DIALING CO LINES (NONE): 
LIST OF CO LINES SUBJECT TO TOLL 
RESTRICT (ALL): 
LIST OF CO LINES EXEMPT FROM ARS 
ONLY (NONE): 
REVIEW CO LINE STATUS AGAIN (N)? 
LINE KEY ASSIGNMENT FOR CO LINE X.Y 
SOFT KEY GROUP X...

PROGRAMMING 
Issue 2, May 1990 ‘. INTER-TEL PRACTICES 
GMX.48 INSTALLATION & MAINTENANCE 
B. [CB] 41.0. LINE GROUPS (/LGRP) 
6.8 
A line group is accessed for placing outgoing 
calls by entering one of the select line group feature 
codes at a station. To define the eight line groups, en- 
ter B from the C.O. lines menu or enter CB or 
/LGRP from the database programming menu. Pre- 
pare to use this program by making a list of the C.O. 
line circuit numbers to be used for each line group (refer to Figure...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE ‘.. 
PROGRAMMING 
Issue 2, May 1990 
C. [CC] SPECIFIC C.O. LINE INFORMATION 
(/LINE) 
6.10 To assign C.O. line features on a line-by-line 
basis, enter C from the CO. lines menu or enter CC 
or /LINE from the database programming menu. Be- 
fore using this program, determine the following in- 
formation for each equipped C.O. line circuit. (The 
program planning sheet in Figure 5-8,page 5-145, may 
be helpful.) 
C.O. lines equipped: List all equipped...