Inter-Tel GMX-48 INSTALLATION & MAINTENANCE Manual

PROGRAMMING 
Issue 2, May 1990 ‘, 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
3.5 
From the database programming menu prompt 
(selection [A] from the applications menu), any of 
these commands can be used: 
MENU LEVEL, 
[A] DATABASE PROGRAMMING 
[A] General System Data 
[AA] Date and Time 
[AB] Timer Values 
[AC] System Speed Dial 
[AD] Account Codes 
[AE] Reminder Messages 
[AF] Miscellaneous System Data 
[AG] DND Messages 
[AH] Passwords DATE 
TIMR 
SPDI 
ACCT 
MESS 
MISC 
DNDM 
PASS 
[B]...

[A] GENERAL SYSTEM DATA 
[B] EXTENSIONS AND FEATURE 
ACCESS CODES CODE 
[C] CO LINES 
[D] STATlONlDSS DATA 
[E] HUNT GROUPS HUNT 
[F] TENANTS, ATTENDANTS, AND 
SECRETARIAL INTERCEPTS - 
[G] PAGE ZONES PAGE 
[HI TOLL RESTRICTION 
[I) AUTOMATIC ROUTE SELECTION - 
[J] DATABASE SAVE/RESTORE SAVE 
-p, [K] SYSTEM INlTlALlZATlON 
APPLICATIONS PROGRAM MENU AND RESET INIT 
[A] DATABASE PROGRAMMINQ I 
[B] SMDR AND ERROR PROGRAMMING 
ICI SAR PROGRAMMING -, 
1 
II I 
_I 
[A] SMDR OUTPUT OUTR 
[B] SMDR REPORTS SMDR...

PROGRAMMING 
Issue 2, May 1990 ‘.. 
INTERaTEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
4. [A] GENERAL SYSTEM DATA 
4.1 Choose option A from the database program- 
ming menu to program general system data. The 
menu appears as shown below: 
[A] GENERAL SYSTEM DATA 
NOTE: Selection [H] PASSWORDS does not appear 
unless the unrestricted password was entered or no 
password is required. 
A. [AA] DATE AND TIME (/DATE) 
[A] DATE AND TIME 
[B] TIMER VALUES 
[C] SYSTEM SPEED DIAL 
[D] ACCOUNT CODES 
[E]...

.’ INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE ‘.. 
PROGRAMMING 
Issue 2, May 1990 
SYSTEM TIME @X:xX): EITHER, enter the hour and the minutes in 
. 
24hour international time (midnight is 0O:CKl; noon 
is 12:OO)and . 
OR, change only the hour or minutes using one of 
the following methods: 
l Enter two digits (00-23) and c CR > to change 
the hour. 
l Change the minutes by entering a colon (:), two 
digits @O-59), and < CR > . 
PERFORM UPDATE TO SYSTEM DATABASE 
(Y OR N) 
This prompt appears...

PROGRAMMING 
Issue 2, May 1990 
‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
B. [AB] TIMER VALUES (/TIMR) 
4.3 There are programmable timers that control 
various system functions. In this programming task, 
the programmer can change any or all of them. To 
reach this program, enter B from the general system 
data menu or enter Al3 or /+T’IMR from the database 
programming menu. on the following pages. The default values have been 
carefully selected to ensure proper system operation...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, May 1990 
TlMER 
Keyset Hookswitch Debounce 
Off-Line After Disconnect 
Reminder Message Scroll Delay 
SL Hookflash Minimum 
SL Hookflash Maximum 
Voice Mail/Computer Dialing 
Delay 
Camp-On 
Camp-On Tone 
CO Re-Seize lO/lO 
l-50 
10110 10-250 
5110 O-50 
2/10 l-10 
7110 2-20 
5110 O-100 
3 sec. O-255 
15 sec. 
3 sec. 5-255 
1-15 
DEFAULT 
PURPOSF 
After detecting a valid hookswitch toggle, the length 
of time the system will...

PROGRAMMING 
Issue 2, May 1990 ‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION 8z MAINTENANCE 
Data Port Wait 
Dial Tone Wait 
Dial Initiation - Keyset 
Dial Initiation - SL Set 
Disconnect Wait After Dialing 
Forward No Answer 
Hold 
Inactivity Alarm 
Interdigit (Long) 
Interdigit (Short) 
Line Pre-Select 
Message (At Message Center) 
OHVA Screening 
paging 
Pause Digit 30 sec. l-255 
2 sec. l-50 
15 sec. 5-30 
10 sec. 5-30 
20 sec. 2-30 
15 sec. 3-255 
60 sec. lo-255 
60 sec. lo-255 
15 sec. 2-255 
4 sec....

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE ‘.. 
PROGRAMMING 
Issue 2, May 1990 
TlMER 
Queue Callback 
Recall 
Station Monitoring Tone 
Transfer - Available 
Transfer - Busy 24 sec. 
Valid Call 15 sec. 
Abandoned Recall 
Unsupervised Conference 
Unsupervised CO 
YAl IJF 
15 sec. 
60 sec. 
15 sec. 
20 sec. 
10 min. 
5 min. 
5 min. 
DEFAULT 
RANGE 
lo-255 
lo-255 
5-255 
lo-255 
lo-255 
O-60 
l-255 
l-255 
l-255 
PURPOSE 
Time allowed for a station to respond to a queue 
callback before the...

PROGRAMMING 
Issue 2, May 1990 ‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
REVIEW SAME TIMERS AGAIN (N) 
TIMER VALUES IN TENTHS OF SECONDS 
DIALING WAIT AFTER CONNECT (15): 
DIALING WAIT AFTER HOOKFLASH (30): 
INTER-RING SILENCE (60): 
KEYSET HOOKSWITCH DEBOUNCE (10): 
OFF-LINE AFTER DISCONNECT (10): 
REMINDER MESSAGE SCROLL DELAY (5): 
SL HOOKFLASH MINIMUM (2): 
SL HOOKFLASH MAXIMUM (7): 
VOICE MAIL/COMPUTER DIALING DELAY 
(5): 
REVIEW SAME TIMERS AGAIN (N) 
TIMER VALUES IN SECONDS...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, May 1990 
STATION MONITORING TONE (15): 
TRANSFER - AVAILABLE (20): 
TRANSFER - BUSY (24): 
VALID CALL (15): 
REVIEW SAME TIMERS AGAIN (N) 
TIMER VALUES IN MINUTES 
ABANDONED RECALL (10): 
UNSUPERVISED CONFERENCE (5): 
UNSUPERVISED CO (5): 
REVIEW SAME TIMERS AGAIN (N) 
PERFORM UPDATE TO SYSTEM DATABASE 
Cy ORN) 5-255 (Not available in Basic software) 
lo-255 
lo-255 . 
Enter Y < CR > to return to the CAMP-ON 
prompt. Or, enter...