Inter-Tel GMX-48 INSTALLATION & MAINTENANCE Manual

PROGRAMMING 
Issue 2, May 1990 .. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
C. [AC] SYSTEM SPEED DIAL (BPDI) 
4.7 
To prepare for programming the system speed- 
dial information, determine the following informa- 
tion. (If desired, use the program planning sheet in 
Figure 5-2 on page 5-134.) 
System speed-dial programming station: Deter- 
mine the circuit or intercom number of the keyset 
station that will be allowed to program all system 
speed-dial numbers, including all tenant-specific...

./ INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE ‘.. 
PROGRAMMING 
Issue 2, May 1990 
PERFORM UPDATE TO SYSTEM DATABASE 
(Y OR N) 
RANGE OF SPEED DIAL NUMBERS TO BE 
REVIEWED (NONE): 
N( >: SPEED DIAL NAME 0: 
TENANT 
GROUP NUMBER (NONE): 
. . . 
20 ( ): 
SPEED DIAL NAME 0: 
TENANT 
GROUP NUMBER (NONE): 
REVIEW SAME SPEED DIAL NUMBERS Y- Return to the first speed-dial number of the 
AGAIN (N)? selected range. 
N- Continue to the next prompt. 
PERFORM UPDATE TO SYSTEM DATABASE 
(Y OR N) 
REVIEW...

PROGRAMMING 
Issue 2, May 1990 ‘, 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
D. [AD] ACCOUNT CODES (/ACCT) 
4.9 
Enter D from the general system data menu or 
enter AD or /ACCT from the database programming 
menu to define up to 32 standard account codes and 
up to 120 forced account codes, using this program. 
(For more information regarding account codes, refer 
to page 4-55 in FEATURES.) These codes can then 
be assigned to specific stations in program [D] (Sta- 
tion/DSS Data). 
4.10 If...

‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, May 1990 
O( 1: 1 [ASSOC STN 1.11 ( ): 
. . . 
47 [ASSOC STN 6.7]( ): 
48 [ASSOC STN 6.8]( ): 
. . . 
60 [ASSOC STN 8.6]( ): 
61( ): 
119 ( ): 
REVIEW SAME FORCED ACCOUNT CODES 
AGAIN (N)? 
REVIEW ADDITIONAL. FORCED ACCOUNT 
CODES (N)? 
PERFORM UPDATE TO SYSTEM DATABASE 
(Y OR N) As each forced account code number appears, 
enter the four- to eight-digit code. Or, enter c to 
erase the current code without entering a new...

PROGRAMMING 
Issue 2, May 1990 
‘, 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
F. [AF] MISCELLANEOUS SYSTEM DATA 
(/MISC) 
4.14 
Various system parameters are set using this 
programming task. Select F from the general system 
data menu or enter AF or /MISC from the database 
programming menu. 
4.15 To prepare for this program, determine the fol- 
lowing information. If desired, use the program plan- 
ning sheet in Figure 5-5 on page 5-138. 
Primary attendant or system alarm station: Re-...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, May 1990 
are speed dialed (via ARS, redial, station 
speed dial, system speed dial, etc.), or if they 
will be muted. 
- 
Hardware handshake settings: Determine 
whether the RS-232-C connectors on the 
KSU and/or Accessory Port Modules should 
be set for “hardware” or “software” hand- 
shaking. Refer to page 2-16 in SPECIFICA- 
TIONS for details. 
- 
Speed-dial programming hookjlash: Determine 
whether hookflashes can be...

PROGRAMMING 
Issue 2, May 1990 . . 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION 8~ MAINTENANCE 
PRIMARY AmNDANT STATION (1.1): 
SYSTEM ALARM STATION (1.1): 
BROADCAST ALARMS TO ALL Y- System alarms display on all attendants’ 
AmNDANTS (Y): keysets. 
N- Only the primary attendant (or system alarm 
station) is notified in the event of a system alarm. 
DAY/NIGHT MODE TOGGLE STATION (1.1): If desired, enter the circuit (X.Y) or intercom 
(EXXX) number of the keyset station that will 
cause the system to be...

INTER-TEL PRACTICES 
GMX.48 INSTALLATION & MAINTENANCE PROGRAMMING Issue 2, May 1990 
CO LINE PRIVACY RELEASE (N): 
DTMF TONES DURING SPEED DIALING 
(N): 
HARDWARE HANDSHAKE FOR PRIMARY Y- The CPU port will be enabled for hardware and 
PORT (N): software handshaking. 
HARDWARE HANDSHAKE FOR 
ACCESSORY PORT A (N): 
HARDWARE HANDSHAKE FOR 
ACCESSORY PORT B (N): 
HOOKFLASH PROGRAMMING IN SPEED 
DIAL NUMBERS (Y): 
LCD IDENTIFICATION FOR KEYSET 
FULL-TIME (N): 
OFF-HOOK VOICE ANNOUNCE (N): 
Page 5-27 Y-...

PROGRAMMING INTER-TEL PRACTICES 
Issue 2, May 1990 ‘- GMX-48 INSTALLATION & MAINTENANCE 
IMMEDIATE DSS OFF-HOOK VOICE 
ANNOUNCE (Y): This prompt appears only if the OHVA feature is 
enabled, 
Y- 
DSS stations can make immediate OHVA calls 
without waiting for the OHVA screening timer to 
expire. 
N- DSS stations do not have special priority when 
making OHVA calls. 
OVERRIDE SCOS WITH SYSTEM SPEED 
DIAL NUMBERS (N): Y- System speed dial numbers can be dialed from 
any station regardless of SCOS. 
N-...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 2, May 1990 
G. [AG] DND MESSAGES (/DNDM) 
4.17 
Select program G from the general system data menu or enter AG or /DNDM from the database program- 
ming menu to define any or all of the do-not-disturb message displays (2-20). (For more information regarding 
do-not-disturb messages, refer to page 4-86 in FEATURES.) Refer to the program planning sheet in Figure 5-6 
on page 5-139. The prompts appear as shown below. End each entry...