Inter-Tel GMX-48 INSTALLATION & MAINTENANCE Manual

INTER-TEL PRACTICES FEATURES 
GMX-48 INSTALLATION & MAINTENANCE Issue 2, May 1990 
21.11 If 
a station in a linear or distributed hunt 
group is in call forward mode, the station will not re- 
ceive hunt group calls. However, if a station in an all- 
ring hunt group is in call forward mode, the line key 
will flash to indicate a ringing hunt group call (but the 
station will not ring). 
::’ 
:, 
21.12 Call forwarding overrides any secretarial in- 
tercept assignment. 
21.13 When a station that is...

FEATURES 
Issue 2, May 1990 INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
intercom dial tone when the timer expires. Either 
party can reset the timer by pressing any DTMF key 
before the SL dial initiation timer expires. If the un- 
supervised C.O. timer is not reset, the call recalls the 
attendant. If the attendant does not answer the recall 
before the abandoned recall timer expires, the call is 
disconnected. 
NOTE: There may be some reduction in voice volume 
when an outside call is...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE FEATURES 
Issue 2, May 
1990 
Forwarding To the Message Center Forwarding To Voice Mail 
21.24 Keyset users have a simple method for for- 
warding calls to the their designated message center. 
The user presses the FWD key and then the MSG 
key. Calls forwarded through the keyset are then sent 
to the keyset’s designated message center. 
21.25 
TO QUICKLY FORWARD CALLS TO YOUR MES- -. SAGE CENTER (KEYSETS ONLY): 
While on or off hook, press the FWD...

FEATURES 
INTER-TEL PRACTICES 
Issue 2, May 1990 GMX-48 INSTALLATION 8z MAINTENANCE 
22. SPEED DIALING 
22.1 Three GMX-48 features provide speed- 
dialing. They are as follows: 
a 
A, System Speed Dialing: 
Up to 100,32-digit system 
or tenant-specific speed-dial numbers can be 
stored in system memory. 
Station 
Speed Dialing: Single-line set users can 
store up to 10, 16-digit outside numbers using 
speed-dial location codes (O-9). Using the ten 
speed-dial (SPD/BLF) keys, keyset users can 
store 10...

‘. 
INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE FEATURES 
Issue 2, May 1990 
22.9 
To program system speed-dial numbers, use 
one of the following methods: 
e 
l 
:_: 
:; 
e 
Use the keypad to manually dial the number. If 
you make a mistake, press the MUTE key to back- 
space. 
Press the REDL key to enter the last number 
dialed or saved at the station (up to 
32 digits). 
Press one of the SPD/BLF keys on the keyset to 
enter the outside telephone number (up to 16 dig- 
its) programmed under...

FEATURES 
INTER-TEL PRACTICES 
Issue 2, May 1990 GMX-48 INSTALLATION & MAINTENANCE 
accepted. (Display shows PROGRAM SYS- 
TEM SPEED DIAL.) 
(6) 
EITHER, repeat steps 2 through 5 for each 
number to be entered or changed. 
OR, wait for the display to return to the date 
and time (after the long interdigit timer ex- 
pires) or lift and replace the handset. 
22.12 
TO ERASE SYSTEM SPEED-DLAL NAMES ANDIOR 
NUMBERS (ATTENDANTSAND THE DESIGNATED SYSTEM 
SPEED-DlAL PROGRAMMING KEYSET ONLY): 
(1) 
(2) 
(3) 
(4)...

‘. 
INTER-TEL PRACTICES FEATURES 
GMX.48 INSTALLATION & MAINTENANCE 
Issue 2, May 1990 
Dialing System Speed-Dial Numbers 
22.15 TO DIAL SYSTEM SPEED-DL4L. NUMBERS: 
Single-Line Set: Press the FLASH key (hook- 
flash) and enter the system speed-dial feature 
code (381). 
(1) Lift the handset and select an outgoing line. (3) Enter the location code (00-99) for the desired 
number. The number is automatically dialed. 
(Display shows the number dialed unless 
it is a 
(2) Keyset: 
Press the SYS SPD key (or...

FEATURES INTER-TEL PRACTICES 
Issue 2, May 1990 GMX-48 INSTALLATION & MAINTENANCE 
B. STATION SPEED DIALING 
22.16 
For convenience, each station user can pro- 
gram individual speed-dial numbers. Single-line set 
users can store up to 10, 16-digit outside numbers 
using speed-dial location codes (O-9). Using the 
speed-dial (SPD/BLF) keys and/or location codes, 
1Zline and 24-line keyset users can store 10 outside 
telephone numbers (up to 16 digits each) and 10 inter- 
com numbers (up to four digits...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE FEATURES 
Issue 2, May 1990 
You hear a single progress tone when the sys- 
tem has accepted the number. (Display shows 
both numbers stored under the key.) 
(4) Lift and replace the handset (or wait 5 seconds 
for the display to return to the date and time). 
Repeat the steps for each additional number 
to be stored. 
22.22 
TO PROGRAM STATION SPEED-DIAL NUMBERS 
USING A SINGLE-LINE SET: 
NOTE: Up to 10 outside telephone numbers can be 
stored using...

FEATURES 
Issue 2, May 1990 INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
23. INTERCOM AND C.O. DIRECTORY 
(KEYSETS ONLY) 
NOTE: This feature is available only in the Intermedi- 
ate 
and Advanced software packages. 
23.1 The intercom directory enables display keyset 
users to “look up” intercom extension numbers and 
user names. The C.O. directory enables display key- 
set users to “look up” system speed-dial numbers and 
associated names. The intercom directory is automat- 
ically updated...