Inter-Tel GMX-48 INSTALLATION & MAINTENANCE Manual

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE FEATURES 
Issue 2, May 1990 
16. CALL TRANSFER 
16.1 There are several feature codes for transfer- 
ring intercom and outside calls to other stations or to 
outside telephone numbers. The call transfer options 
are: 
l’kansfer C.O. call: You can transfer outside calls 
to another station or to an outside telephone 
number. 
lkansfer intercom call: Intercom calls can be 
transferred to another station or to an outside 
telephone number. 
‘Ikansfer to...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE FEATURES 
Issue 2, May 1990 
17. REVERSE TRANSFER AND GROUP 
CALL PICK-UP 
17.1 Calls ringing or recalling at a station, a hunt 
group, or a transfer-to-park location can be picked up 
at any other station, using these features. Calls on 
hold can also be picked up from stations and from 
transfer-to-park locations. 
NOTE: When reverse transferring a direct ring-in 
call, the line or OVER key will continue to flash at the 
ringing station until the...

FEATURES INTER-TEL PRACTICES 
Issue 2, May 1990 GMX-48 INSTALLATION & MAINTENANCE 
18. CALL PRIVACY AND PRIVACY 
RELEASE 
18.1 Call privacy restricts speech channel access to 
one station at a time. When a C.O. line or intercom 
channel is selected, no other station user can gain ac- 
cess to the line or channel. However, access to, and 
control of, a line or channel can be passed to another 
station using the conference or transfer features. 
182 In addition, the database contains an installer-...

INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE FEATURES 
Issue 2, May 1990 
19. CONFERENCE CALLS 
19.1 Station users can establish a three- to five- 
party conference without operator assistance. A 
station user can initiate one conference at a time and 
the system can maintain up to eight simultaneous 
conference calls. In addition to the initiating station, 
the conference can include any combination of inter- 
com and/or outside calls. The initiating station is con- 
sidered one of the...

FEATURES 
INTER-TEL PRACTICES 
Issue 2, May 1990 
GMX-48 INSTALLATION & MAINTENANCE 
B. ADDING PARTIES TO A CONFERENCE 
NOTE: 
Only one party in the conference can perform 
this procedure at a time. This procedure cannot be 
performed if five parties are already in the confer- 
ence. 
19.6 TO ADD PARTIES TO AN EXISTING CONFERENCE 
(ANYINSIDE PARW: 
Keyset: 
(1) During the conference, press the CNF key. 
The other parties remain connected. The CNF 
key flutters and the line keys remain lit to indi- 
cate...

INTER-TEL PRACTICES FEATURES 
GMX-48 INSTALLATION & MAINTENANCE Issue 2, May 1990 
Single-Line Set: 
Access one party by pressing 
the FLASH (hookflash) key and then pressing 
the HOLD key (or entering the individual hold 
feature code - 336). Then you can place it on 
hold, disconnect it, or re-establish the confer- 
ence (following the procedures in paragraph 
19.5). Repeat this step to access additional par- 
ties. 
19.9 
TO EXIT THE CONFERENCE AND LEAVE THE 
OTHERPARTIESCONNECTED(ANYINSIDEPARTY):...

FEATURES 
Issue 2, May 1990 INTER-TEL PRACTICES 
GMX-48 INSTALLATION & MAINTENANCE 
21. CALL FORWARDING 
21.1 With call forwarding, a station user can route 
incoming calls to another station, to a hunt group, or 
to an outside telephone number (if programmed for 
forwarding to the public network and allowed by toll 
and line restrictions). Station users can determine 
whether intercom and outside calls or just outside 
calls will be forwarded when placing the station into 
call forward mode. Special...