HP Z5200 Owners Manual

2. Paper Drive
The Paper Drive test diagnoses Failures of components of the Media-Axis. You must perform the Paper
Drive Test after:
● System Error Code 81:XZ.
● System Error Code 41:XZ.
● System Error Code 73:XZ.
Diagnostic tests also need to be performed after removing or replacing certain printer components. If
you have removed or replaced printer components,  check the Service Calibration Guide to Removal
and Installation to see which tests and calibrations you need to perform. Refer to 
Service...

3.The Front Panel then displays the Main PCA Revision (this value should be always between 0 and
3.3) and prompts you to press any key to continue.
4.Press any key to continue.
5. The Front Panel displays the following messages:
●Starting Nvm.
● Getting Part Number.
● Checking PCA rev.
● Prog slow PWM paper.
6. The Front Panel then prompts you to remove the media.
7.Remove the media.
8. Press any key to continue.
9. The Front Panel then displays the Open Loop ROLL test result.
10.Press any key to...

13.The Front Panel then displays:
● Starting Paper Motor.
● Starting Paper Axis.
● Calib. Analog Decoder.
14. The Front Panel then displays the Analog Decoder calibration results.
● The GAIN for channel A must be 
between 0 and 3.5.
● The GAIN for channel B must be 
between 0 and 4.5.
● The OFFSET for channel A must be 
between -63.5 and 63.5.
● The OFFSET for channel B must be 
between 63.5 and 63.5.
15. If the results are correct, press  OK to accept the results. If the results are not correct, press...

23.The Front Panel prompts you to shutdown  the printer to complete the test.
24.Press any key to shutdown the printer.
3. Electronics Module
The Electronics Module test diagnoses Failures of the following components:
●Main PCA components.
● Electronics Module to Carriage interfacing.
● Print Mech PCA components.
● Power Supply Unit voltages.
Diagnostic tests also need to be performed after removing or replacing certain printer components. If
you have removed or replaced printer components, check the...

4.The Power supply test starts and the Front Panel displays the following messages:
● Starting Horsburgh.
● Starting DelSol7.
● Starting Carriage.
● Getting PSU voltages.
5. The Front Panel then displays the Power Supply test results.
6.Press any key to continue.
7. The Fan Speed test starts and the Front Panel displays:
● Starting Horsburgh.
● Starting Tests PWM.
● Starting Tests GPIO.
● Booting up the Carriage.
8. The Front Panel then displays the Fan Speed test result and prompts you to press any key...

13.The Front Panel then displays PCA Rev. Voltage test result and prompts you to press any key to
continue.
14.Press any key to continue.
15. The Formatter memory size test starts and  the Front Panel displays the following messages:
● Starting DelSol1.
● Getting PCA Revision.
● Checking Memory Size.
16. The Front Panel then displays Formatter Memory Size and prompts you to press any key to
continue.
17.Press any key to continue.
18. The Formatter hard disk test starts and the Front Panel displays the...

●Checking Memory Size.
● Getting HDA Info.
● Getting File System Info.
22. The Front Panel then displays Formatter Hard Disk File informatio n test results and prompts you
to press any key to continue.
23. Press any key to continue.
24. The Main Board Revision Voltage test starts an d the Front Panel displays the following messages:
● Starting DelSol1.
● Getting PCA Revision.
● Checking Memory Size.
● Getting HDA Info.
● Getting File System Info.
● Getting MainBoard Rev.
25. The Front Panel then displays...

28.The Front Panel then displays Main Memory size  test results and prompts you to press any key to
continue.
29. Press any key to continue.
30. The Front Panel then prompts you to  test the Formatter Communications.
31.Press  OK to the test the Formatter. If you do  not wish to test the Formatter use the  Arrow keys to
select NO  and press  OK.
32. The Formatter Communications test starts and  the front Panel displays the following messages:
● Starting Micci2Bus.
● Starting Micci2BusProxy.
● Checking...

36.The Front Panel then displays the Plotter Information results and prompts you to press any key to
finish.
37.Press any key to finish.
38. The Front Panel shows the test co mplete display for a few seconds.
39.The Front Panel prompts you to shutdown the printer to complete the test.
40.Press any key to shutdown the printer.
4. Carriage Assembly
The Carriage assembly test diagnoses Failures of any components of the Carriage. Always run this test
before replacing the Carriage Assembly.
Diagnostic tests...

●Getting Carriage PCA Rev
● Starting Nvm.
3. The Front Panel prompts you to verify  the Carriage Assembly PCA revision.
The PCA Rev must be  between 0.823 and 1.005 .
4.If the results are correct, press  OK to accept the results. If th e results are not correct, press  Back
  Cancel  to reject the result s and FAIL the test.
5. The Carriage Assembly test starts  and the Front Panel displays the following messages followed
by their results:
● Getting Part Number.
● Getting Scan Access size.
● Getting Vs...