HP Z5200 Owners Manual

The Star Wheel Lifter subassembly is designed to move the Start Wheel support to the up and down
positions. This is used to load roll or sheet medi a and avoid damage to the Star Wheel caused by paper
jams etc.
Perform the Scan Axis - Star wheel lifter test as follows:
NOTE:Perform this test with the Printheads and the Tubes System installed in order to get values
that can be compared correctly.
1. In the Diagnostics menu, scroll to 1. Scan Axis  and press OK.
2. The Front Panel will show the1. Scan Axis...

●Analyzing motor traces.
● Checking PWM results.
● Checking SWL PWM Backward.
● Moving & Getting traces.
● Moving SWL Motor
● Dumping motor traces.
● Analyzing motor traces.
● Checking PWM results.
If there is a Failure at any point during the test, the Front Panel will display the relevant System
Error Code. To troubleshoot any displayed error codes, refer 
System Error Codes - Full
Descriptions on page 50 .
5. Once the test has been completed the Front Panel displays the test results.
6. Press any key...

NOTE:Perform this test with the Printheads and the Tubes System installed in order to get values
that can be compared correctly.
1. In the Diagnostics menu, scroll to 1. Scan Axis and press OK .
2. The Front Panel will show the1. Scan Axis  submenu.
3.In the  Scan Axis  submenu, scroll to PRS and press  OK to start the test. The Printer will start the
Scan Axis subsystem Common Initialization and PRS test  initialization. If there is a Failure at any
point during the tests,  the Front Panel will display...

If there is a Failure at any point during the test, the Front Panel will display the relevant System
Error Code. To trouble shoot any displayed error codes, refer 
System Error Codes on page 46.
5. Once the test has completed the Fr ont Panel displays the test result.
6.Press any key finish.
7. The Front Panel shows the test co mplete display for a few seconds.
8.The Front Panel prompts you to shutdown  the printer to complete the test.
9.Press any key to shutdown the printer.
Scan Axis Test
The Scan...

NOTE:Perform this test with the Printheads and the Tubes System installed in order to get values
that can be compared correctly.
1. In the Diagnostics menu, scroll to 1. Scan Axis  and press OK .
2. The Front Panel  will show the 1. Scan Axis submenu
3.In the  Scan Axis  submenu, scroll to  Scan Axis and press  OK to start the test.
The Printer will start the Scan  Axis subsystem Common Initializati on. If there is a Failure at any
point during the tests,  the Front Panel will display the relevant...

6.The Front Panel prompts you to confirm that  the carriage supply LED is switched on.
7.Open the Window and verify that the LED is on. The LED can be seen through the slots in the
carriage cover.
8. Press  OK if the LED is on. If the LED is not on or use the  Arrow keys to select  NO and press
OK  .
9. The printer then continues the Scan Axis test. As the test executes the Front Panel displays the
following messages:
●Booting Up Carriage.
● Getting Part Number.
● Getting Scan Axis Size
● Preparing SVS....

16.The printer then continues the Scan Axis test. As  the test executes the Front Panel displays the
following messages:
● Preparing SVS.
● Prog slow PWM scan.
● Moving Carriage middle.
● Starting Carriage.
● Encoder.
17. The Front Panel prompts you to move the carriage to check the encoder readings.
18.Use the Arrow  keys to move the Carriage left or right as prompted to by the Front Panel.
19. Repeat step 18 to complete the ten Carriage movements used to check the encoder.
20. The Front Panel displays...

23.The Front Panel displays the PWM check results.
24.Press any key finish.
25. The printer then continues the Scan Axis test. As the test executes the Front Panel displays the
following messages:
●Moving PRS to High Position.
26. The Front Panel displays the PRS position check results.
27.Press any key finish.
28. The Front Panel shows the test co mplete display for a few seconds.
29.The Front Panel prompts you to shutdown  the printer to complete the test.
30.Press any key to shutdown the printer....

Perform the Scan Axis - Cutter test as follows:
1.In the Diagnostics menu, scroll to 1. Scan Axis  and press OK.
2. The Front Panel will show the1. Scan Axis   submenu.
3.In the  Scan Axis  submenu, scroll to Cutter and press  OK to start the test.
The Printer will start the Scan  Axis subsystem Common Initializati on and Cutter test initialization.
If there is a Failure at any point during the tests, the Front  Panel will display the relevant System
Error Code . To trouble shoot any disp layed error...

5.The Front Panel prompts you to load roll media.
6.Raise the Media Lever, load roll media, lower the Media Lever, and press any key to continue.
7. The printer then starts an actual test cut of the media. As the test executes the Front Panel displays
the following messages:
●Advance paper.
● Engaging cutter.
● Cutting paper.
● Disengaging cutter.
8. Once the test has completed the Fr ont Panel displays the test result.
9.Press any key finish.
10. The Front Panel shows the test co mplete display for a...