HP Z5200 Owners Manual

2.The Front Panel  will show the 7. IDS submenu.
3.In the IDS submenu, scroll to  Ink Delivery System  and press OK to start the test.
4. The Ink Delivery System test starts and the fron t Panel prompts you to remove all the Ink Supplies.
5.Remove all the Ink Cartridges.
6. Press  OK to continue.
7. The test continues and the front Panel displays the following messages:
● Starting Horsburgh.
● Starting Mips.
● Starting Nvm.
● Getting Part Number.
● Starting ISS Motors.
● Moving Bongos down.
● Reading...

11.Release Bongo0.
12. Press any key.
13. The Front Panel then displays the Bongo0 test results.
14.Press any key to continue.
15. Repeat steps 8 through 14 for the remaining Out of Ink sensors for each of the Ink Cartridges.
16. The front Panel prompts you to insert all the Ink Supplies.
17.Install all the Ink Cartridges.
18. Press  OK to continue.
19. The Acumen Supplies test and the front Panel displays the following messages:
●Starting AcumenSupplies.
● Reading AcumenSupplies.
20. The Front Panel...

22.The Front Panel prompts you to shutdown the printer to complete the test.
23.Press any key to shutdown the printer.
Check Ink Supplies
1. In the Diagnostics menu, scroll to 7. IDS  and press OK.
2. The Front Panel will show the7. IDS  submenu.
3.In the  IDS submenu, scroll to Check Ink Supplies  and press OK to start the test.
4. The Check Ink Supplies test starts and the  front Panel displays the following messages:
● Starting Horburgh & Mips.
● Starting Nvm.
● Getting Part Number.
● Starting...

7.The Front Panel shows the test co mplete display for a few seconds.
8.The Front Panel prompts you to shutdown  the printer to complete the test.
9.Press any key to shutdown the printer.
Check Leakage
1. In the Diagnostics menu, scroll to  7. IDS and press OK.
2. The Front Panel will show the7. IDS submenu.
3.In the  IDS submenu, scroll to Leakage and press  OK to start the test.
4. The Check Ink Leakage test checks that ther e is no ink in the tubes or ink cartridge
8. Service Station
The complete...

Diagnostic tests also need to be performed after removing or replacing certain printer components. If
you have removed or replaced printer components, check the Service Calibration Guide to Removal
and Installation to see which tests and calibrations you need to perform. Refer to 
Service Calibration
Guide to Removal and Installation on page 170 .
Service Station
1. In the Diagnostics menu, scroll to 8. Service Station and press  OK.
2. The Front Panel will show the8. Service Station  submenu.
3.In the...

●Homing Scan Axis.
● Starting ServicingServices.
● Capping Service Station.
● Uncapping Service Station.
● Starting Mechanical Init.
5. The Front Panel then prompts you to  check the status of the printer.
6.Check that:
●The Window is closed.
● The Media Lever is lowered.
● All Printheads are inserted.
● Valid Cartridges are inserted.
7. Press  OK to continue.
8. The Front Panel then displays test results.
9.Press any key to finish the test.
10. The Front Panel shows the test co mplete display for a few...

11.The Front Panel prompts you to shutdown the printer to complete the test.
12.Press any key to shutdown the printer.
Primer Motor
1. In the Diagnostics menu, scroll to 8. Service Stationand press  OK .
2. The Front Panel  will show the 8. Service Station  submenu.
3.In the  8. Service Station  submenu, scroll to  Primer Motor and press OK to start the test.
4. The Primer Motor test starts and the fr ont Panel displays the following messages:
● Starting TestsGpio.
● Starting Horsburgh.
● Booting up...

●Moving to Spit Front pos.
● Moving to Wipe forward pos.
● Moving to Wipe reverse pos.
● Moving to Cleaner pos.
● Moving to Color Sensor (ESP) pos.
● Homing Scan Axis.
● Starting ServicingServices.
● Capping Service Station.
● Uncapping Service Station.
● Starting Mechanical Init.
5. The Front Panel then prompts you to  check the status of the printer.
6.Check that:
●The Window is closed.
● The Media Lever is lowered.
● All Printheads are inserted.
● Valid Cartridges are inserted.
7. Press  OK to...

10.The Front Panel prompts you to shutdown the printer to complete the test.
11.Press any key to shutdown the printer.
Aerosol Fan
1. In the Diagnostics menu, scroll to 8. Service Station and press  OK.
2. The Front Panel will show the8. Service Station  submenu.
3.In the 8. Service Station submenu, scroll to  Aerosol Fan and press OK to start the test.
4. The Aerosol Fan test starts and the fr ont Panel displays the following messages:
● Starting Horsburgh.
● Booting TestsGpio.
● Starting Nvm.
5. The...

7.The test continues and the Front Panel displays the results.
8.Press any key to continue.
9. The front panel prompts you to check if the Aerosol Fan is operating.
10.Listen carefully to check if the Aerosol Fan is operating.
11. If it is operating, use the  Arrow keys to select  YES and press  OK . If it is NOT operating, select
NO  and press  OK .
12. The Front Panel shows the test result.
13.Press any key to finish.
14. The Front Panel shows the test co mplete display for a few seconds.
15.The Front...