HP Z5200 Owners Manual

Perform the Turn Drive Roller utility as follows:
1.In the Service Utilities submenu, scroll to  Turn Drive Roller and press OK.
2. The Printer checks to see if me dia is loaded and the Front panel displays the following message.
If media is loaded, t he Front Panel will display a message.  Unload the media and start again from
step 1:
● Checking Media Presence Sensor
3. The Drive Roller begins to turn slowly and the following message is displayed on the Front Panel:
4.Refer to the Cleaning Instructions...

NOTE:REMEMBER TO REMOVE THE PIECE OF  PAPER FROM THE WINDOW SENSOR
BEFORE CLOSING THE WINDOW AS THIS COUL D DAMAGE THE WINDOW AND THE SENSOR.
2. Purge Tubes
The purpose of this Service Utility is to Prime the Tubes when the Ink Tubes are NOT new and they
need to be re-primed or automatic priming was not completed correctly.
NOTE: Make sure that NEW Ink Cartridg es are installed or that the ink volume remaining in the Ink
cartridges is below 88% before st arting to prime the tubes. If you do not comply,...

6.Install the Setup Printheads in the carriage.
7.Once all the Setup Printheads are installed, the foll owing message will appear on the front panel.
Close the carriage cover and close the window.
8. The printer will begin to  purge the tubes system.
9. Once the tubes system has been  purged, the following message will instruct you to open the
Window and the carriage to access the printheads:
10. When the following message appears on the Front  Panel, open the Carriage cover and check the
window on top...

12.Once ALL the Printheads are insta lled, the Front Panel will instruct you to close the Carriage cover
and close the Window.
13. The Printer will now perf orm the Printhead Alignm ent and Front Panel will prompt you to continue
with the Printhead Alignment, select  Align now and press the OK  key.
14. Once the Printhead Alignment is  completed, the following message  will be displayed on the Front
Panel. Press the  OK key to continue.
3. Set SN
The purpose of this Service Utility  is to set the Serial...

4.If the utility exits correctly,  OK will be displayed  on the Front Panel.
5. When the printer is restarted after a serial num ber change an NVM setting sequence is initiated to
synchronize the serial number stored in the backup memory.
4. Reset Life Counters
The purpose of this Service Utility  is to reset the internal life counters. There are two submenus that
allow you to:
● Reset ALL the counters related to a Preventive Maintenance Kit (PMK).
● Reset only the counters related to a specific replaced...

●Scan Motor
● Left Spittoon
● Right Spittoon
● Full Bleed Foams
● Aerosol Fans
● Carriage
● Service Station
3. Once you have selected a Life  Counter to reset, the following message will be displayed on the
Front Panel. Press the  OK key to reset the selected Life Counter or press  Back  Cancel  to exit
without resetting the Life Counter.
If the Usage Counter information cannot be read,  the Front Panel will display “Unable to get usage
counter”. This could be a possibl e Firmware error. In this case,...

Perform the Set Date and Time utility as follows:
1. In the Service Utilities submenu, scroll to  Set Date and Time and press OK.
2. The Printer will display the current time and the new time. Use the  UP and Down  k e y s  t o  g o  t h r o u g h
the digits and press the  OK key to go to the next digit. You can press the  Cancel key at any time
to exit the utility without making any changes.
3. Once the new time has been entered, the Front Panel prompts you to confirm the new date and
time.
4.Press  OK...

Perform the Enable/Disable Firewall utility as follows:
1. In the Service Utilities submenu, scroll to Enable/Disable Firewall  and press OK.
2. The utility checks to see if the firewall is enabl ed or disabled and the Front panel displays the
following message:
● Getting Information of Firewall.
3. When the following message appears on the fron t panel, you must select whether you would like
to enable or disable the firewall. Use the  UP and  Down  keys to make your selection and press
the  OK key.
4....

Configure the Enable/Disable Sleep mode utility as follows:
1. In the Service Utilities submenu, scroll to  Enable/Disable Sleep Mode and press OK.
2. The Front Panel tells you whether sleep mode  is currently enabled or disabled. Press OK to
continue or Cancel to leave th e sleep mode status unchanged.
3.The Front Panel displays the sleep mode status. Press  OK to return to the menu.
9. SNMP Language Write Access
The purpose of this utility is to prevent SNMP to ols from changing the printer language...

2.The utility checks whether the printer language  can currently be changed using SNMP, and shows
one of the following messages:
3. Use the Up and Down keys to choose the desired behavior and press  OK to confirm your selection.
The system updates the internal memory  to reflect the chosen selection.
4.The Front Panel shows the “test complete” display until you press  OK.
136 Chapter 4   Service Menu ENWW