HP Deskjet F735 User Manual

Solution 3: Check for a paper jam 
Solution: Clear the paper jam. 
For more information, see: 
“Clear paper jams” on page 92 
Cause: The product had a paper jam. 
If this did not solve the issue, try the next solution.
Solution 4: Load more  paper in the input tray 
Solution: If the product has only a few sheets remaining, load more paper in the 
input tray. If there is plenty of paper in the input tray, remove the paper, tap the stack 
of paper against a flat surface, and reload the paper into the input...

Solution 6: Check the cable connections to the product 
Solution: If the product is not properly connected to the computer, communication 
errors can occur. Try the following:
If the connections are secure, and nothing has printed several minutes after you sent
a print job to the product, check the status of the product. In the HP Photosmart 
Software, click  Settings, and then click Status. 
For more information, see:
“After setting up the product, it does not print” on page 86
Cause: The computer was...

Solution 9: Check the print driver status 
Solution: The printer driver status might have changed to either Offline or Stop 
printing . 
To check the printer driver status 
▲ In the HP Solution Center, click the Status tab. 
Cause: The status of the printer driver has changed. 
If this did not solve the issue, try the next solution.
Solution 10: Check the print queue for canceled jobs 
Solution: A print job might remain in the queue after it has been cancelled. The 
cancelled print job jams the queue and...

Nothing happens when I try to print
Try the following solutions to resolve the issue. Solutions are listed in order, with the most 
likely solution first. If the first solution does not solve the problem, continue trying the 
remaining solutions until the issue is resolved. 
•Solution 1: Make sure that the product is turned on 
•Solution 2: Wait for the product to finish other tasks 
•Solution 3: Select the correct printer
•Solution 4: Check the cable connections to the product 
•Solution 5: Load more...

Solution 4: Check the cable connections to the product 
Solution: If the product is not properly connected to the computer, communication 
errors can occur.
If the connections are secure, and nothing has printed several minutes after you sent
a print job to the product, check the stat us of the product. In the HP Photosmart 
Software, click  Settings, and then click Status. 
Cause: The computer was not communicating with the product. 
If this did not solve the issue, try the next solution.
Solution 5:...

Solution 7: Check for a print carriage stall 
Solution: Turn off the product. Lower the input tray, open the front access door, 
and remove any objects that are blocking the print carriage (including any packing 
materials), and then turn on the product.
For more information, see: 
“The print carriage is stalled” on page 191 
Cause: The print carriage has stalled.
The pages in my document came out in the wrong order 
Solution: Print the document in reverse order. When the document finishes 
printing, the...

Make sure the margin settings for the document do not exceed the printable area of 
the product. 
To check your margin settings 
1. Preview your print job before sending it to the product. 
In most software a pplications, click the File menu, and then click Print Preview. 
2. Check the margins. 
The product uses the margins you have set in your software application, as long 
as they are greater than the minimum margins the product supports. For more
information about setting margins in your software...

NOTE:To avoid paper jams, tuck the flaps inside the envelopes.
For more information, see: 
“Load envelopes” on page 28
Cause: A stack of envelopes was loaded incorrectly.
Text or graphics are cut off at the edge of the page
Try the following solutions to resolve the issue. Solutions are listed in order, with the most 
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved. 
•Solution 1: Check the margins in your...

Solution 2: Check the layout of the document 
Solution: Make sure the layout of the document you are trying to print fits on a paper 
size supported by the product. 
To preview the print layout 
1. Load the correct paper size into the input tray. 
2. Preview your print job before sending it to the product. 
In most software a pplications, click the File menu, and then click Print Preview. 
3. Check the graphics in the document to make sure that the current size fits within 
the printable area of the...

A blank page came out while printing
Try the following solutions to resolve the issue. Solutions are listed in order, with the most 
likely solution first. If the first solution does not solve the problem, continue trying the 
remaining solutions until the issue is resolved. 
•Solution 1: Check the ink levels in the print cartridges 
•Solution 2: Check for blank pages at the end of the document
•Solution 3: Load more paper in the input tray
•Solution 4: Check the print cartridges for protective tape...