HP Deskjet F735 User Manual

To clean the area around the ink nozzles 
1. Turn on the product and open the print cartridge door. 
The print carriage moves to the far right side of the product.
2. Wait until the print carriage is idle and silent, and then unplug the power cord from 
the back of the product. 
3. Lightly press down on the print cartridge to release it, and then pull it towards you out 
of the slot.
NOTE: Do not remove both print cartridges at the same time. Remove and clean 
each print cartridge one at a time. Do not...

7.Hold the print cartridge with the HP logo on top, and insert the print cartridge back 
into the slot. Make sure you push the print cartridge in firmly until it snaps into place.
8. Repeat if necessary for the other print cartridge. 
9. Gently close the print cartridge door and plug the power cord into the back of the 
product.
Related topics 
“Clean the print cartridges” on page 74
Remove ink from your skin and clothing
Follow these instructions to remove ink from your skin and clothing:
SurfaceRemedy...

Chapter 10 
80 Maintain the HP All-in-One
Maintain the HP All-in-One
 

11 Shop for ink supplies
For a list of print cartridge numbers, see the printed documentation that came with the 
HP All-in-One. You can also use the software  that came with the HP All-in-One to find 
out the reorder number for all the print cartridges. You can order print cartridges online 
from the HP Web site. Additionally, you can contact a local HP reseller to find out the
correct print cartridge reorder numbers for your product and purchase print cartridges. 
To order genuine HP supplies for the...

Chapter 11 
82 Shop for ink supplies
Shop for ink supplies
 

12 Troubleshooting
This section contains the following topics: 
•View the Readme file 
•Setup troubleshooting 
•Paper jams 
•Print cartridge troubleshooting 
•Print quality troubleshooting
•Print troubleshooting
•Copy troubleshooting 
•Scan troubleshooting 
•Errors
View the Readme file
You might want to refer to the Readme file for information on system requirements and 
possible installation problems. 
You can access the Readme file by clicking  Start, pointing to Programs or All 
Programs , pointing to...

This section contains the following topics: 
•The product will not turn on 
•I connected the USB cable, but I am having problems using the HP All-in-One with
my computer
•After setting up the product, it does not print
•When I insert the CD-ROM into my computer’s CD-ROM drive, nothing happens 
•The Minimum System Checks screen appears 
•A red X appears on the USB connect prompt
•I received a message that an Unknown Error has occurred
•The registration screen does not appear 
•Some of the buttons are...

•If you are using a power strip, make sure the power strip is on. Or, try plugging 
the product directly into a power outlet. 
• Test the power outlet to make sure it is working. Plug in an appliance that you 
know works, and see if the appliance has power. If not, then there might be a
problem with the power outlet. 
• If you plugged the product into a switched outlet, make sure the outlet is switched 
on. If it is switched to on but still does not work, then there might be a problem 
with the power...

If you installed the software, uninstall it and then reinstall it, connecting the USB cable 
only when prompted.
For more information on installing the software and connecting the USB cable, see 
the Start Here guide that came with the product. 
Cause: The USB cable was connected before the software was installed. 
Connecting the USB cable before prompted can cause errors.
After setting up the product, it does not print 
Solution: 
• Look at the On button located on the product. If it is not lit, the...

•Make sure your computer is USB ready and that you are using a supported 
operating system. For more info rmation, see the Readme file. 
• Check the connection from the product to your computer. Verify that the USB 
cable is securely plugged into the USB port on the back of the product. Make sure 
the other end of the USB cable is plugged into a USB port on your computer. After
the cable is connected properly, turn the product off and then on again.
• If you are connecting the product through a USB hub,...