HP Deskjet F735 User Manual

Solution 1: Check the print settings 
Solution: Check the print settings. 
• Check the paper type setting to make sure it matches the type of paper loaded in 
the input tray. 
• Check the quality setting. Use a higher quality setting to increase the amount of 
ink used for printing. 
For more information, see: 
•“Set the paper type for printing” on page 33 
•“Change the print speed or quality” on page 34
•“Print using Maximum dpi” on page 41 
•“Make a Fast copy” on page 56 
Cause: The paper type or print...

Solution 4: Clean the glass 
Solution: Clean the glass and lid backing. 
For more information, see: 
•“Clean the lid backing” on page 66 
•“Clean the glass” on page 65 
Cause: Debris might be stuck on the glass or on the back of the document lid; this 
causes poor copy quality and slows down processing. 
If this did not solve the issue, try the next solution.
Solution 5: Check the print catridges 
Solution: Check the estimated ink levels in the print cartridges.
NOTE:Ink level warnings and indicators...

Printouts seem blurry or fuzzy
Try the following solutions if your printout is smudged or unclear.
NOTE:There is no problem with the ink supplies and replacing the print cartridges 
is unnecessary.
TIP: After reviewing the solutions in this section, you can go to HPs support Web 
site to see if there is additional troubleshooting help. For more information, go to:
www.hp.com/support .
•Solution 1: Check the print settings 
•Solution 2: Use a higher quality image 
•Solution 3: Print the image in a smaller...

If a digital photo or rasterized graphic has been resized, it can be blurry or fuzzy when 
printed. 
Cause: The image was printed in a larger size.
Printouts have vertical streaks 
Solution: HP recommends that you use HP Advanced Papers or any other paper 
type that is appropriate for the product. 
Always make sure the paper you are printing on is flat. For best results when printing 
images, use HP Advanced Photo Paper. 
Store photo media in its original packaging inside a resealable plastic bag on a...

Solution 3: Check the rear access door 
Solution: Make sure the rear access door is securely installed. 
Cause: The rear access door was not securely installed.
Ink streaks on the back of the paper
Try the following solutions if there is smeared ink on the back of your printout. 
•Solution 1: Print on a page of plain paper 
•Solution 2: Wait while the ink dries 
Solution 1: Print on a page of plain paper 
Solution: Print one or several pages of plain paper to soak up any excess ink in 
the product. 
To...

Solution 1: Make sure the paper is loaded correctly 
Solution: Make sure that the paper is loaded correctly in the input tray. 
For more information, see: 
“Load paper” on page 24 
Cause: The paper was not loaded correctly. 
If this did not solve the issue, try the next solution.
Solution 2: Check the print settings
Solution: Check the print settings. 
• Check the paper type setting to make sure it matches the type of paper loaded in 
the input tray. 
• Check the quality setting. Use a higher quality...

3.Dip the lint-free cloth into the purified or distilled water, and squeeze any excess 
water from it. 
4. Clean the rubber rollers to remove any dust or dirt buildup. 
5. Replace the rear access door. Gently push the door forward until it snaps into 
place.
6. Plug the power cord back in, and turn on the product. 
7. Try to print again. 
Cause: The rollers were dirty and needed to be cleaned. 
If this did not solve the issue, try the next solution.
Solution 4: Contact HP support for service
Solution: If...

TrueType iconOpenType icon
Cause:The font was a custom size. 
Some software applications offer custom fonts that have jagged edges when enlarged 
or printed. Also, if you want to print bitmapped text, it might have jagged edges when 
enlarged or printed. 
If this did not solve the issue, try the next solution.
Solution 2: Align the print cartridges 
Solution: Align the print cartridges. 
For more information, see:
“Align the print cartridges” on page 73 
Cause: The print cartridges needed to be aligned....

For more information, see: 
“Load envelopes” on page 28
Cause: A stack of envelopes was loaded incorrectly. 
If this did not solve the issue, try the next solution.
Solution 2: Load a different type of envelope
Solution: Do not use shiny or embossed envelopes or envelopes that have clasps 
or windows. 
Cause: The wrong type of envelope was loaded. 
If this did not solve the issue, try the next solution.
Solution 3: Tuck the flaps to avoid paper jams
Solution: To avoid paper jams, tuck the flaps inside...

Solution 2: Use the appropriate media 
Solution: To print a borderless image, use 10 x 15 cm (4 x 6 inch) HP Advanced 
Photo Papers. 
For more information, see: 
“Print a borderless image” on page 38 
Cause: Use of inappropriate media.
The product is not responding
Try the following solutions to resolve the issue. Solutions are listed in order, with the most 
likely solution first. If the first solution does not solve the problem, continue trying the 
remaining solutions until the issue is resolved....