Fujitsu Series 3 Manual
Here you can view all the pages of manual Fujitsu Series 3 Manual. The Fujitsu manuals for Controller are available online for free. You can easily download all the documents as PDF.
Page 651
1. Configuration Chapter: PPG Configuration This chapter explains PPG configuration. 1. Configuration CODE: 9BFPPGTOP-E01.2 FUJITSU SEMICONDUCTOR LIMITED CHAPTER 16-1: PPG Configuration MB9Axxx/MB9Bxxx Series MN706-00002-1v0-E 615
Page 652
1. Configuration 1. Configuration This section explains the unique PPG configuration. The following shows the unique PPG configuration. PPG output GATE Signal Circuit PPG1 PPG Trigger Enable Register Timing Generator Circuit 0 To interrupt unit GATE signal (GATE0, GATE2, GATE4, GATE8, GATE10, GATE12) RTO output PPG module PPG0 PPG2 PPG4 PPG3 PPG5 PPG7 PPG6 PPG8 PPG9 PPG10 PPG11 PPG12 PPG13 PPG14 PPG15 Multi Function Timer Unit 0 Multi Function TimerUnit 1 RTO output RTO output RTO output RTO...
Page 653
1. Configuration FUJITSU SEMICONDUCTOR LIMITED Chapter: PPG Configuration FUJITSU SEMICONDUCTOR CONFIDENTIAL 4 Combinations of operation modes and PPG channels with output enabled PPG channel 8-bit mode 8+8-bit mode 16-bit mode 16+16-bit mode PPG ch.0 PPG0 output PPG0 output PPG ch.1 Not available PPG0 prescaler PPG0 output PPG0 output PPG ch.2 PPG2 output PPG2 output PPG ch.3 Not available PPG2 prescaler PPG2 output PPG0 prescaler PPG ch.4 PPG4 output PPG4 output PPG ch.5...
Page 655
1. Overview Chapter: PPG This chapter describes the PPG timer. 1. Overview 2. Configuration and Block Diagrams 3. Operations 4. Setup Procedure Example 5. Registers 6. Notes CODE: 9BFPPG-E01.2 FUJITSU SEMICONDUCTOR LIMITED CHAPTER 16-2: PPG MN706-00002-1v0-E 619 MB9Axxx/MB9Bxxx Series
Page 656
1. Overview 1. Overview This section describes the overview of PPG timer. The Programmable Pulse Generator (PPG) module can perform pulse output of arbitary cycle and duty ratio controled by timer operation. Features of PPG module 8-bit PPG output 2-channel independent operating mode is supported. 16-bit PPG output operating mode is supported. 8+8-bit PPG output operating mode is supported. 16+16-bit PPG output operating mode is supported. PPG can be inverted the output...
Page 657
2. Configuration and Block Diagrams 2. Configuration and Block Diagrams This section shows the configuration and block diagrams of PPG timer. PPG circuit block diagram Figure 2-1 shows the block diagram of the PPG circuit. Figure 2-1 PPG circuit block diagram PPG output APB SignalAPB Interface PPG Output Circuit Interrupt Output Circuit Control Registers DOWN counter Reload Circuit To interrupt unit GATE signal from multifunction timer PPG module GATE Signal Circuit PPG Trigger...
Page 658
2. Configuration and Block Diagrams Timing generator block diagram Figure 2-2 and Figure 2-3 show the block diagram of timing generator circuits 0 and 1, respectively. Figure 2-2 Block diagram of timing generator circuit 0 FUJITSU SEMICONDUCTOR LIMITED STRMONI Figure 2-3 Block diagram of timing generator circuit 1 In Figure 2-2 and Figure 2-3 , PPGxTG(x=0,2,4,6,8,10,12,14) is a PPG start trigger signal. The Timi ng Ge nerator Circuit consists of the following functional...
Page 659
3. Operations 3. Operations This section shows the opration of PPG timer. 3.1 PPG circuit operations 3.2 Timing generator circuit operations FUJITSU SEMICONDUCTOR LIMITED CHAPTER 16-2: PPG MN706-00002-1v0-E 623 MB9Axxx/MB9Bxxx Series
Page 660
3. Operations 3.1. PPG circuit operations The PPG module can output pulse signals having arbitary cycle and duty ratio. The pulse output can be controlled based on the timer operation. PPG functions The PPG timer starts decrem enting the down counter value being set in the LOW width reload register by triggered. During this time, the output is set to LOW. After an underflow occurs, the output is inverted to HIGH. Then, the PPG timer starts decrementing the value being set in the HIGH width...
All Fujitsu manuals