Epson Aculaser CX28DN User Manual

							Configuration Menu Overview 29
KEY 
SPEEDTIME TO 
STARTSetting0.1sec / 0.3sec / 0.5sec / 
1.0sec / 1.5sec / 2.0sec / 
2.5sec / 3.0sec
Specify the length of time until the cursor begins 
to move continuously when a key is held down.
INTERVALSetting0.1sec / 0.3sec / 0.5sec / 
1.0sec / 1.5sec / 2.0sec / 
2.5sec / 3.0sec
Specify the length of time until the cursor contin-
uously moves between settings or characters.
LANGUAGESettingENGLISH / FRENCH / GERMAN / 
ITALIAN / SPANISH / PORTU-
GUESE
 / RUSSIAN / CZECH / 
SLOVAK / HUNGARIAN / POLISH 
/ 
JAPANESE
Select the language of the menus and mes-
sages that appear in the message window.
LAMP OFF TIMESettingMODE1 / MODE2
Select the length of time until the scanner unit 
lamp goes off when no operation is performed.
If 
MODE1 is selected, the lamp goes off when 
the machine enters Preheat mode.
If 
MODE2 is selected, the lamp goes off when 
the machine enters Energy Save mode.
 
						

							Configuration Menu Overview 30
LAMP WARMUP TIMESettingAUTO / FIX
Specify the warm-up time for the lamp of the 
scanner unit.
If 
AUTO is selected, the length of time to 
recover from Energy Save mode when the 
machine is turned on is adjusted according to 
the room temperature. Since the machine can-
not be used until its condition is completely sta-
bilized, select this setting, for example, if you 
wish to scan at a high image quality from the 
first page.
If 
FIX is selected, the machine can be used 
after lamp warm-up is finished. With a low room 
temperature, the quality of the first page of a 
copy or scanned image may not be as good as 
if 
AUTO was selected.
TONER EMPTYSettingSTOP / BW CONTINUE
Select whether or not printing and copying stop 
when the toner has run out.
If 
STOP is selected, printing and copying stop 
when the toner runs out.
If 
BW CONTINUE is selected, monochrome 
printing and monochrome copying can continue 
when one or more color toners run out while 
black toner still remains.
TONER NEAR EMPTYSettingON / OFF
When the toner is nearly run out, a warning 
message appears. 
I-UNIT NEAR EMPTYSettingON / OFF
When the imaging unit is nearly run out, warning 
message appears.
AUTO CONTINUESettingON / OFF
Select whether or not printing continues when a 
size error occurs during printing.
CALIBRATIONSettingON / OFF
Select whether or not to perform image stabili-
zation. If 
ON is selected, image stabilization is 
started.
 
						

							Configuration Menu Overview 31
PAPER SETUP Menu
PAPER SETUP TRAY1 PAPER
TRAY2 PAPER
 
						

							Configuration Menu Overview 32
Manufacturer’s default settings appear in bold.
TRAY1 PAPERMedia typePLAIN PAPER / THICK PAPER / 
THICK PAPER2 / TRANSPARENCY / 
LABELS / LETTERHEAD / GLOSSY / 
GLOSSY2 / ENVELOPE / POSTCARD
Paper size
When a setting other than ENVELOPE 
or 
POSTCARD is selected: A4 / A5 / B5 
/ 
LEGAL / LETTER / G LETTER / 
STATEMENT / EXECUTIVE / FOLIO / 
G LEGAL / CUSTOM
When ENVELOPE is selected: COM10 / 
C6 / DL / MONARCH / CHOU#3 / CUS-
TOM
When POSTCARD is selected: 
J-POSTCARD 100x148 / D-POST-
CARD 148x200
 / CUSTOM
Select the type and size of the media loaded into Tray 
1. If 
CUSTOM is selected as the paper size, specify 
settings for 
LENGTH and WIDTH separately.
The Setting range for 
LENGTH is 148 to 356 mm.
The default setting is 
297 mm.
The Setting range for 
WIDTH is 92 to 216 mm.
The default setting is 
210 mm.
When a media type is selected, a screen appears, 
showing the available media sizes. The available 
media sizes differ depending on the selected media 
type.
The setting for CUSTOM is displayed in 
metric (mm) even if 
ADMIN. MANAGEMENT/
USER SETTING/PRESET ZOOM
 is set to 
INCH.
 
						

							Configuration Menu Overview 33
TRAY2 PAPERPaper sizeA4 / A5 / B5 / LETTER / G LETTER / 
STATEMENT / EXECUTIVE / CUSTOM
Select the size of the media loaded into Tray 2. If 
CUSTOM is selected as the paper size, specify settings 
for 
LENGTH and WIDTH separately.
The Setting range for 
LENGTH is 148 to 297 mm.
The default setting is 
297 mm.
The Setting range for 
WIDTH is 92 to 216 mm.
The default setting is 
210 mm.
Only plain paper can be loaded into Tray 2.
The setting for CUSTOM is displayed in 
metric (mm) even if 
ADMIN. MANAGEMENT/
USER SETTING/PRESET ZOOM
 is set to 
INCH.
 
						

							Configuration Menu Overview 34
ADMIN. MANAGEMENT Menu
The ADMIN. MANAGEMENT menu is accessible only by the adminis-
trator. To display the settings for this menu, select 
ADMIN. MANAGE-
MENT
, use the keypad to type in the 6-digit administrator access code 
(default: 000000), and then press the Select key.
ADMIN. MAN-
AGEMENTADMINISTRATOR 
NO.
NETWORK SET-
TINGTCP/IP
IP ADDR. SET-
TING
*1
DNS*1DNS AUTO SET-
TING
SPECIFY
DHCP
*1
BOOTP*1
ARP/PING*1
HTTP*1
FTP*1
SMB*1
 
						

							Configuration Menu Overview 35
BONJOUR*1
DYNAMIC DNS*1
IPP*1
RAW PORT*1DISABLE/ENABLE
BIDIRECTIONAL
SLP
*1
SNMP*1
WSD PRINT*1
IPSEC*1
IP ADDR. 
FILTER*1ACCESS PER.
ACCESS REFUSE
IPv6
*1DISABLE/ENABLE
AUTO SETTING
*2
 
						

							Configuration Menu Overview 36
LINK LOCAL*2
GLOBAL 
ADDRESS*2
GATEWAY 
ADDRESS*2
NETWARE
APPLETALK
SPEED/
DUPLEX
IEEE802.1X
E-MAIL SETTING SMTP
SENDER NAME
E-MAIL ADDRESS
DEFAULT SUBJECT
SMTP SERVER 
ADDR.
SMTP PORT NO.
 
						

							Configuration Menu Overview 37
SMTP TIMEOUT
TEXT INSERT
POP BEFORE SMTP DISABLE/ENABLE
POP3 SERVER 
ADDR.
*3
POP3 PORT NO.*3
POP3 TIMEOUT*3
POP3 ACCOUNT*3
POP3 PASSWORD*3
SMTP AUTH. DISABLE/ENABLE
SMTP USER 
NAME
*4
SMTP PASSWORD*4
LDAP SETTING DISABLE/ENABLE
LDAP SERVER 
ADDR.
*5
 
						

							Configuration Menu Overview 38
LDAP 
PORT NO.*5
SSL SETTING*5
SEARCH BASE*5
ATTRIBUTE*5
SEARCH 
METHOD*5
LDAP 
TIMEOUT*5
MAX.SEARCH 
RESULTS*5
AUTHENTICATION*5
LDAP ACCOUNT*5
LDAP PASSWORD*5
DOMAIN NAME*5
CAMERA DIRECT
USER SETTING COUNTRY SETTING