Epson Aculaser CX28DN User Manual
Have a look at the manual Epson Aculaser CX28DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Dual In-Line Memory Module (DIMM) 269 2Remove the rear cover. 3Using a screwdriver, loosen the screw. Do not remove any screw other than the one indicated in the illustration. 4Open the inside cover.
Dual In-Line Memory Module (DIMM) 270 5Insert the new DIMM straight into the DIMM connector until the latches snap into the locked position. Observe the keyed side of the DIMM to align it with the connec- tor. If you cannot snap the DIMM into place, do not force it. Repo- sition it, making sure that the DIMM is seated completely in the connector. 6Close the inside cover, and then tighten the screw. 7Close the rear cover. 8Reconnect all interface cables. 9Reconnect the power cord, and turn on the machine. 10Declare the additional Printer Memory in the Windows printer driver (Properties/Configure tab). 11Print a configuration page (REPORT/STATUS / REPORT / CONFIGU- RATION PAGE ) and verify that the total amount of the RAM installed in your printer is listed.
Hard Disk Drive 271 Hard Disk Drive If you install a hard disk drive, the followings can be performed: „Job printing/saving „Fonts/forms/color profile download „User Authentication „Direct printing Installing the Hard Disk drive Note Its very important to protect the printer controller board and any associated circuit boards from electrostatic damage. Before performing this procedure, review the antistatic caution on page 267. In addition, always handle circuit boards by the edges only. 1Turn off the machine and discon- nect the power cord and inter- face cables.
Hard Disk Drive 272 2Remove the rear cover. 3Using a screwdriver, loosen the screw. Do not remove any screw other than the one indicated in the illustration. 4Open the inside cover.
Hard Disk Drive 273 5Plug the cable on the hard disk drive into the connector on the controller board. 6Insert the three mounting pins on the hard disk drive into the holes in the controller board to mount the hard disk drive onto the controller board. 7Close the inside cover, and then tighten the screw. 8Close the rear cover. 9Reconnect all interface cables.
Hard Disk Drive 274 10Reconnect the power cord, and turn on the machine. 11Declare the Hard Disk in the Windows printer driver (Properties/Configure tab).
Tray 3 (Lower Feeder Unit) 275 Tray 3 (Lower Feeder Unit) You can install up to one optional lower feeder unit (Tray 3). The lower feeder unit increases your machine’s media feed capacity by 500 sheets. Kit Contents „Lower feeder unit with a tray (500-sheet capacity)
Tray 3 (Lower Feeder Unit) 276 Installing Tray 3 Note Since consumables are installed in the machine, be sure to keep the machine level when moving it in order to prevent accidental spills. 1Turn off the machine and discon- nect the power cord and inter- face cables. 2Prepare the lower feeder unit. Be sure to place the lower feeder unit on a level surface. 3Open the right side cover of the lower feeder unit. The right side cover of the lower feeder must be opened before the feeder can be installed onto the machine.
Tray 3 (Lower Feeder Unit) 277 4With another person’s help, place the machine on top of the lower feeder unit, making sure that the positioning pins on the lower feeder unit correctly fit into the holes on the bottom of the machine. WARNING! This machine weighs approximately 55 kg (121 lb) when it is fully loaded with consumables. The machine must be lifted by two people. 5Close the right side cover of the lower feeder unit. 6Reconnect all interface cables. 55 kg121 lbs
Tray 3 (Lower Feeder Unit) 278 7Reconnect the power cord, and turn on the machine. 8Declare the Tray 3 in the Windows printer driver (Properties/Configure tab).