Epson Aculaser CX28DN User Manual
Have a look at the manual Epson Aculaser CX28DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Status, Error, and Service Messages 259 NO NETWORK SETTINGThe network set- tings had not been completely specified when the machine was switched to Scan mode.Before scanning in Scan mode, specify the network settings in the NETWORK SET- TING and E-MAIL SETTING menus. NO SUITABLE PAPER LOAD PAPER (xxx)Paper suitable for printing is not loaded in a paper tray.Load paper suitable for printing into a paper tray. NOT INSTALLED I-UNIT CHECK xThe indicated imag- ing unit is not installed.Install the indicated imaging unit. NOT INSTALLED TONER CHECK xThe indicated toner cartridge is not installed.Install the indicated toner cartridge. NOT REGISTEREDNo address destina- tion or group desti- nation is registered.Directly type in the destination address for the scan data, or regis- ter an address destina- tion or group destination and try specifying the destina- tion address again. OUTPUT TRAY FULL REMOVE PAPERThe output tray is full of paper.Remove all paper from the output tray. OVER SEARCH TIMECommunication with the LDAP server has timed out.Establish a connection with the LDAP server again. PAPER EMPTY LOAD PAPER (xxx)The indicated paper tray has run out of paper.Load media into the indicated tray. PAPER SIZE ERROR RESET PAPER (xxx)Paper of the selected size is not loaded in a paper tray.Load paper of the selected size into a paper tray. This message... means... Do this...
Status, Error, and Service Messages 260 REMOVE ORIGINAL IN ADFRThe document is loaded in the ADF while a function is set that requires scanning from the original glass.Place the document on the original glass. RESULTS ARE OVER xxxThe LDAP search results exceed the maximum specified with MAX. SEARCH RESULT in the LDAP SET- TING menu.Change the maximum setting, or change the search conditions (for example, increase the length of the key- word), and then try performing the LDAP search again. SCANNER MOTION ERROR CHECK SCANNER LOCKThe scanner is locked.Move the scanner lock lever to , and then turn the machine off, then on again. For details, refer to “Unlocking the Scan- ner” on page 214. SCANNER UNIT OPEN CLOSE SCANNER UNITThe scanner unit is open.Close the scanner unit. SERVER MEMORY FULL SMTP ServerThe memory of the SMTP server has become full.Free up some space on the disk, for exam- ple, by contacting your server administrator. THE PARTY IS FULLThe maximum num- ber of 236 destina- tions for the scan data has been reached.Send the data, and then try scanning again. Otherwise, delete unnecessary destinations before adding the desired ones. This message... means... Do this...
Status, Error, and Service Messages 261 TONER EMPTY CHANGE x TONERThe indicated toner cartridge has become empty. (This message appears if TONER EMPTY on the MACHINE SET- TING menu is set to STOP.)Replace the indicated toner cartridge. Toner Low xThe indicated toner cartridge is low and should be replaced within 200 pages at 5% coverage of Let- ter/A4 paper.Prepare the indicated toner cartridge. Trans. Belt LifeThe time to replace the transfer belt unit has been reached.Replace the transfer belt unit. Contact a qualified ser- vice representative. Trans. Roll. LifeThe time to replace the transfer roller has been reached.Replace the transfer roller. Contact a qualified ser- vice representative. TRAYx OPEN CLOSE TRAYxThe indicated paper tray is open.Close the indicated paper tray. UNABLE TO COLLATE JOBSince the hard disk (area for saving copies when print- ing sets) is full, cop- ies cannot be printed as sets.Print only one set at a time, or reduce the number of pages to be printed. USB Dev. Not supportA USB device incompatible with this machine is con- nected.Disconnect the USB device from this machine. This message... means... Do this...
Status, Error, and Service Messages 262 USB Hub Not supportA USB hub is con- nected to this machine.This machine is not compatible with a USB hub. When connecting USB cables to this machine, do not use a USB hub. USB MEMORY FULLThere is no space available on the USB memory device connected to this machine.Delete data from the USB memory device to create free space, or use a different USB memory device. xxx COVER OPEN CLOSE xxx COVERThe indicated cover is open.Close the indicated cover. xxx DOOR OPEN CLOSE xxx DOORThe indicated door is open.Close the indicated door. xxx SERVER ERRORThe file cannot be saved on the indi- cated server.Check the status of the indicated server. WASTE TONER FULL REPLACE BOTTLEThe waste toner bottle is full.Replace the waste toner bottle. Waste Near FullThe waste toner bottle will soon be full.Prepare a waste toner bottle. Wrong I-Unit xAn imaging unit incompatible with the machine is installed.Replace the indicated imaging unit with a cor- rect one. WRONG PASSWORD xxxThe password is incorrect, so the indicated server could not be accessed.Check the password, and then specify the correct one. Wrong Toner xA toner cartridge incompatible with the machine is installed.Replace the indicated toner cartridge with a correct one. This message... means... Do this...
Status, Error, and Service Messages 263 Service Messages These messages indicate a more serious fault that can only be corrected by a customer service engineer. If one of these messages appears, turn the machine off, then turn it on again. If the problem persists, contact your local vendor or authorized service provider. xxx IS DISABLEDThe TCP/IP, FTP, SMTP or SMB set- tings are disabled.Enable the TCP/IP, FTP, SMTP or SMB settings. DESTINATION SET BY MANUAL UP TO 16There were more than 16 addresses found with an LDAP search.Increase the number of entered characters, and then perform the search again. This service message... means... Do this... MACHINE TROUBLE SERVICE CALL (xxxx)An error has been detected with the item indicated “ xxxx” in the service message.Reboot the machine. This often clears the service message, and machine opera- tion can resume. If the problem per- sists, contact Techni- cal Support. This message... means... Do this...
Introduction 266 Introduction Note Any damage to the machine caused by the use of accessories not manufactured or supported by Epson will void your warranty. This chapter provides information about the following accessories. Note The hard disk drive cannot be installed to be used at the same time. Installing accessories always requires that the machine and accessories are turned off and unplugged during installation.Dual In-Line Memory Module (DIMM)256 MB, 512 MB DIMM (DDR2-667 SO-DIMM, 166 MHz, 200pins, No ECC, Unbuffered, CL=3) Density : 512 Mbits Organization : 64 Mwords x 8 bits Tray 3Lower feeder unit with 500-sheet tray included Hard Disk Drive40GB Hard Disk
Antistatic Protection 267 Antistatic Protection Note It’s very important to protect the printer controller board from electrostatic damage while performing any task involving the controller board. Turn off all power switches first. If an antistatic wrist strap is provided in your printer option kit, attach one end of it to your wrist and the other end to the bare metal chassis on the back of your printer. Never attach the wrist strap to any piece of equipment with an electrical current present. Plastic, rubber, wood, and painted metal surfaces are not acceptable grounding points. If you don’t have an antistatic wrist strap, discharge your body’s static electric charge by touching a grounded surface before you handle any printer boards or components. Also avoid walking around after grounding yourself.
Dual In-Line Memory Module (DIMM) 268 Dual In-Line Memory Module (DIMM) You may need additional memory (DIMM) for complex graphics and for duplex (double-sided) printing. This machine detects only half of the amount of the installed memory. Dual in-line memory module (or DIMM) is compact circuit board with surface-mount memory chips. There is 256 MB of onboard memory and one available memory expansion slot. The memory can be expanded to a maximum of 768 MB (256 MB + 512MB). Installing a DIMM Note Its very important to protect the printer controller board and any associated circuit boards from electrostatic damage. Before performing this procedure, review the antistatic caution on page 253. In addition, always handle circuit boards by the edges only. 1Turn off the machine and discon- nect the power cord and inter- face cables.