Home > Epson > Printer > Epson AcuLaser C4200DN User Manual

Epson AcuLaser C4200DN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C4200DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 475
    							
    Paper Handling51
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    5. Insert the stack into the cassette, lining it up with both the front and left sides of the cassette, with the printable surface 
    up.
    6. Slide the paper guides to fit the paper you are loading.
     
    						
    							
    52Paper Handling
    7. Reinsert the cassette into the unit.
    Note:
    ❏After loading paper, set the  LC 1 Size through LC 4 Size  
    and  LC 1 Type  through LC 4 Type  settings on the control 
    panel to match the loaded paper size and type.
    ❏ If you have installed and loaded paper into the optional paper 
    cassette unit, set the setting for the cassette that you are using.
    Output tray
    New :t he
     information
     about t
    he o
    ther
     o
    utput
     tray, quote
     from t
    he
     similar p
    roduct/
     Face d
    ownThe output tray is located on the top of the printer. Since printouts 
    are output face-down, this tray is also referred to as the face-down 
    tray. Raise the stopper to prevent your printouts from slipping off 
    the printer.
     
    						
    							
    Paper Handling53
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    Note:
    This tray can hold up to 250 sheets. The printer automatically stops 
    printing if the total thickness  of the printout reaches 36 mm.
    Printing on Special Media
    You can print on special media which include Epson paper such 
    as the following. 
    Note:
    Since the quality of any particular brand or type of media may be changed 
    by the manufacturer at any time, Epson cannot guarantee the quality of 
    any type of media. Always test samp les of media stock before purchasing 
    large quantities or printing large jobs.
    EPSON Color Laser Paper
    Ne w  :Color o
    nly/ with c
    ontrol
     panelWhen loading EPSON Color Laser Paper, you should make paper 
    settings as shown below:
    ❏ Make settings on the Basic Settings in the printer driver.
     
    						
    							
    54Paper Handling
    ❏
    You can also make these settings on the  Tray Menu in the 
    control panel. See Tray Menu on page 219.
    EPSON Color Laser Transparencies
    Ne w
     :Color o
    nly/with
     control
     panel/ i
    ncluding
     t
    he
     information
     about d
    uplex
     printing/quote
     the i
    nformation f
    rom s
    imilar
     product
     (how t
    o
     l
    oad t
    ransparencies)Epson recommends the use of EPSON Color Laser 
    Transparencies.
    Note:
    Duplex printing is not available for transparencies.
    Transparencies can be loaded into the MP tray only. When using 
    transparencies, you should make paper settings as shown below:
    ❏ Make settings on the Basic Settings in the printer driver.
    ❏ You can also make these settings on the  Tray Menu in the 
    control panel. See Tray Menu on page 219. Paper Size: A4
    Paper Source: MP Tray (up to 150 sheets or up to 15 
    mm thick stack)
    Lower Cassette  (up to 550 sheets or 
    up to 61 mm thick stack in each 
    cassette)
    Paper Type: Semi-Thick
    Paper Size: A4 or  LT
    Paper Source: MP Tray (up to 15 mm thick stack)
    Paper Type: Transparency
     
    						
    							
    Paper Handling55
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    ❏When the Paper Type setting in the printer driver is set to 
    Transparency , do not load any other type of paper except 
    transparencies.
    Please note the following when handling this media:
    ❏ Hold each sheet by its edges, as oil from your fingers may 
    transfer to the surface and damage the printable surface of the 
    sheet. The Epson logo appears on the printable side.
    ❏ When loading transparencies in the MP tray, insert the short 
    edge first as shown below.
    ❏ If transparencies are loaded incorrectly, the message  Check 
    Transparency  appears on the LCD panel. Remove the 
    jammed transparencies from the printer. To clear the jam, see 
    When transparencies are jammed at the MP tray on page 
    377. 
    c
    Caution:
    Sheets that have just been printed on may be hot.
     
    						
    							
    56Paper Handling
    Envelopes
    New
     :with
     control
     panel/
     including t
    he
     information
     about
     duplex
     printingThe print quality of envelopes may be irregular because different 
    parts of an envelope have different thicknesses. Print one or two 
    envelopes to check the print quality.
    c
    Caution:
    Do not use window envelopes. The plastic on most window 
    envelopes will melt when it comes into contact with the fuser.
    Note:
    ❏ Depending on the quality of envelopes, the printing environment, 
    or the printing procedure, envelopes might be wrinkled. Make a trial 
    print run before you print on a lot of envelopes.
    ❏ Duplex printing is not available for envelopes.
    When loading envelopes, you should make paper settings as 
    shown below:
    ❏ Make settings on the Basic Settings in the printer driver.
    ❏ You can also make these settings on the  Tray Menu in the 
    control panel. See Tray Menu on page 219.
    Please note the following when handling this media. Paper Size:
    IB5 or  DL
    Paper Source: MP Tray (up to 15 mm thick stack)
     
    						
    							
    Paper Handling57
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    ❏Load envelopes with the short edge first as shown below.
    ❏ When printing on DL size envelopes, load them with the long 
    edge first.
    ❏ Do not use an envelope that has glue or tape on it.
    c
    Caution:
    Make sure that the minimum size of envelopes meets the 
    following size requirements:
    1. Minimum length of a long edge: 176 mm
    2. Minimum length of a short edge: 110 mm
    Labels
    New :with c ontrol
     panel/ i
    ncluding
     the
     information a
    bout
     d
    uplex
     printing
    1
    2
     
    						
    							
    58Paper Handling
    You can load up to 15 mm thickness of labels into the MP tray at 
    a time. However, you may need to feed some labels one sheet at 
    a time, or load them manually.
    Note:
    ❏
    Duplex printing is not available for labels.
    ❏ Depending on the quality of labels, the printing environment, or the 
    printing procedure, labels might be wrinkled. Make a trial print run 
    before you print on a lot of labels.
    When loading labels, you should make paper settings as shown 
    below:
    ❏ Make settings on the Basic Settings in the printer driver.
    ❏ You can also make these settings on the  Tray Menu in the 
    control panel. See Tray Menu on page 219.
    Note:
    ❏ You should only use labels design ed for laser printers or plain-paper 
    copiers.
    ❏ To prevent the label adhesive from  coming into contact with printer 
    parts, always use labels that comp letely cover the backing sheet, with 
    no gaps between the individual labels.
    ❏ Press a sheet of paper on top of each  sheet of labels. If the paper sticks, 
    do not use those labels in your printer.
    ❏ You may have to make the setting  Thick* for Paper Type  in the 
    Setup Menu .
    * When using especially thick labels, set  Paper Type to ExtraThk .
    Paper Size:
    A4 or LT
    Paper Source: MP Tray (up to 15 mm thick stack)
    Paper Type: Labels
     
    						
    							
    Paper Handling59
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    3
    Thick paper and extra thick paper
    New :with c
    ontrol
     panel/ i
    ncluding
     the i
    nformation a
    bout
     duplex
     printing/If
     unnecessary, delete
     note t
    extYou can load thick paper (106 to 163 g/m²) or extra thick paper 
    (164 to 216 g/m²) into the MP tray.
    When loading thick or extra thick paper, you should make paper 
    settings as shown below:
    ❏ Make settings on the Basic Settings in the printer driver.
    Note:
    When using extra thick paper, you cannot do duplex printing 
    automatically. When you want to do duplex printing with extra 
    thick paper, set the Paper Type  setting on printer driver to Extra 
    Thick (Back) , then do the duplex printing manually.
    ❏ You can also make these settings on the  Tray Menu in the 
    control panel. See Tray Menu on page 219.
    Loading a custom paper size
    N ew :with c ontrol
     panel/ i
    ncluding
     the
     information a
    bout MacYou can load non-standard size paper (88.9  × 139.7 mm to 220  × 
    355.6 mm) into the MP tray.
    When loading a custom paper size, you should make paper 
    settings as shown below:
    ❏ Make settings on the Basic Settings in the printer driver. Paper Size: A4, A5 , B5 , LT , HLT , EXE , GLT
    Paper Source: MP Tray (up to 15 mm thick stack)
    Paper Type: Thick or Extra Thick
    Paper Size: User Defined Size
     
    						
    							
    60Paper HandlingNote:
    ❏
    For Windows, access the printer driver, then select 
    User-Defined Size  from the Paper Size list on the  Basic 
    Settings  tab. In the User Defined Paper Size dialog box, adjust 
    the Paper Width, Paper Length, and Unit settings to match 
    your custom paper. Then click  OK and your custom paper size 
    will be saved.
    ❏ For Macintosh, access the printer driver, click  Custom Size in 
    the Paper Setting dialog box. Then click  New, adjust the Paper 
    Width, Paper Length, and Margin settings to match your 
    custom paper. Then enter the setting’s name, and click  OK to 
    save your custom paper size.
    ❏ You can also make these settings on the  Tray Menu in the 
    control panel. See Tray Menu on page 219.
    ❏ If you cannot use the printer driver as explained above, make 
    this setting at the printer by accessing the control panel’s 
    Printing Menu  and selecting CTM (custom) as the  Page Size 
    setting. Paper Source: MP Tray (up to 15 mm thick stack)
    Paper Type: Plain, Semi-Thick , Thick  or Extra 
    Thick
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C4200DN User Manual