Home > Epson > Printer > Epson AcuLaser C4200DN User Manual

Epson AcuLaser C4200DN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C4200DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 475
    							
    Cleaning and Transporting the Printer341
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    6. Hold the transfer unit by the orange tabs and lower it into the printer, making sure that it fits into the guides. Push the 
    transfer unit in and up until it clicks into place.
     
    						
    							
    342Cleaning and Transporting the Printer
    7. Pull the transfer unit toward you and push the orange tabs 
    into place.
    w
    Warning:
    Be careful not to touch th e fuser, which is marked CAUTION 
    HIGH TEMPERATURE , or the surrounding areas. If the 
    printer has been in use, the fuser and the surrounding areas 
    may be very hot.
     
    						
    							
    Cleaning and Transporting the Printer343
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    8. Close cover A.
    9. Turn on the printer.
    Cleaning the photoconductor unit
    If printouts have dots at every 30 mm, wipe a roller in the 
    photoconductor unit with a dry soft cloth or cotton swab. 
    Follow the steps below to clean the photoconductor unit.
    c
    Caution:
    Do not take too much time to clean the photoconductor. Exposing 
    the photoconductor to too much light may damage the printer.
    1. Turn off the printer.
     
    						
    							
    344Cleaning and Transporting the Printer
    2. Press the latch on cover A and open the cover.
    3. Raise cover D.
     
    						
    							
    Cleaning and Transporting the Printer345
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    4. Hold the photoconductor unit by the handle, and slowly lift it straight out of the printer.
    w
    Warning:
    Be careful not to touch th e fuser, which is marked CAUTION 
    HIGH TEMPERATURE , or the surrounding areas. If the 
    printer has been in use, the fuser and the surrounding areas 
    may be very hot.
     
    						
    							
    346Cleaning and Transporting the Printer
    5. Place the printout that has dots on it and the photoconductor 
    unit on a flat table as shown below.
    Note:
    ❏Make sure to align the center of the printout and center of the 
    photoconductor unit when positioning them.
    ❏ Place the printout faceup so the  short edge that comes out of the 
    printer first is against the photoconductor unit as shown in the 
    diagram.
     
    						
    							
    Cleaning and Transporting the Printer347
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    6. Look for the roller that is the same color as the dots on the printout. Then, look for the place on the roller that is vertically 
    in the same position as the dots on the printout.
    a. Yellow
    b. Magenta
    c. Cyan
    d. Black
    Note:
    The illustration indicates that the dots on the printout are magenta 
    as an example.
    a
    b
    cd
     
    						
    							
    348Cleaning and Transporting the Printer
    7. Turn the gray part of the black roller to find the spot.
    c
    Caution:
    Be careful not to scratch the su
    rface of the drum and rollers. 
    Also, avoid touching the drum an d rollers, since oil from your 
    skin may permanently damage their surface and affect print 
    quality.
    8. Wipe the spot off the black roller with a dry soft cloth or cotton  swab.
     
    						
    							
    Cleaning and Transporting the Printer349
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    10
    c
    Caution:
    ❏Be careful not to scratch th e surface of the drum (green 
    roller) and rollers (black rollers). Also, avoid scratching 
    the drum and rollers, since oil from your skin may 
    permanently damage their surface and affect print 
    quality.
    ❏ Do not expose the photoconductor unit and the developer 
    cartridge to light any longer than necessary.
    ❏ Do not store the photoconductor unit in an area subject 
    to direct sunlight.
    9. Holding the handle firmly, lower the photoconductor unit  into the printer, making sure the posts on the sides of the unit 
    slide into the slots.
     
    						
    							
    350Cleaning and Transporting the Printer
    w
    Warning:
    Be careful not to touch the fuser, which is marked CAUTION 
    HIGH TEMPERATURE , or the surrounding areas. If the 
    printer has been in use, the fuser and the surrounding areas 
    may be very hot.
    10. Close covers D and A.
    11. Turn on the printer.
    Transporting the Printer
    Ne w :F or
     l
    arge-size
     product/ q
    uote
     t
    he
     information
     from
     the
     similar
     product
     a
    nd
     confirm
     the
     specification f
    or
     optional
     paper
     cassette
    Finding a place for the printer
    New :i
    ncluding t
    he i
    nformation
     about
     optional
     product
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C4200DN User Manual