Home > Epson > Printer > Epson AcuLaser C4200DN User Manual

Epson AcuLaser C4200DN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C4200DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 475
    							
    Installing Options291
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    3. Loosen the three screws on the back of the printer.
    4. Pull out the circuit board tray.
     
    						
    							
    292Installing Options
    5. Identify the memory slot. Its position is shown below.
    * Memory slot
    6. Hold the memory module and insert it into the slot in the  orientation shown below until it stops. Then press both sides 
    of the memory module down. Confirm that the notch on the 
    memory module matches that of the memory slot.
    *notch
    *
    *
     
    						
    							
    Installing Options293
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    c
    Caution:
    ❏Do not apply too much force.
    ❏ Be sure to insert the memo ry facing the correct way.
    ❏ Do not remove any modules from the circuit board. 
    Otherwise, the printer will not work.
    7. Slide the circuit board tray into the printer.
     
    						
    							
    294Installing Options
    8. Fasten the circuit board tray with the three screws.
    9. Reattach the cover.
    10. Reconnect all the interface cables and the power cord.
    11. Plug the printer’s power cord into an electrical outlet.
    12. Turn on the printer.
    To confirm that the option is installed correctly, print a Status 
    Sheet. See Printing a Status Sheet on page 377.
    Note for Windows users:
    If EPSON Status Monitor is not installed, you have to make settings 
    manually in the printer driver. See Making Optional Settings on page 
    95.
    Note for Macintosh users:
    When you have attached or removed pr
    inter options, you need to delete 
    the printer using  Print Setup Utility  (for Mac OS X 10.3),  Print 
    Center  (for Mac OS X 10.2 or below), or  Chooser (for Mac OS 9), 
    and then re-register the printer.
     
    						
    							
    Installing Options295
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    Removing a memory module
    c
    Caution:
    Before you remove a memory module, be sure to discharge any 
    static electricity by touching a grounded piece of metal. 
    Otherwise, you may damage static-sensitive components.
    w
    Warning:
    Be careful when working inside the printer as some components 
    are sharp and may cause injury.
    Note:
    If the optional Hard Disk Drive is in stalled, remove it before uninstalling 
    a memory module.
    Perform the installation procedure in reverse.
    Hard Disk Drive
    The optional Hard Disk Drive allows you to expand the printer’s 
    input buffer when the Ethernet interface is used, and gives you 
    additional memory for graphics, form data, and faster multi-page, 
    multi-output sorting.
    Installing the Hard Disk Drive
    N ew :q uote t
    he
     information
     from the
     similar
     product/
     delete n
    ote
     text i
    n
     hostbase p
    roduct
     (except
     new h
    ostbase).Follow the steps below to install the Hard Disk Drive.
    c
    Caution:
    Before you install the Hard Disk  Drive, be sure to discharge any 
    static electricity by touching a grounded piece of metal. 
    Otherwise, you may damage static-sensitive components.
     
    						
    							
    296Installing Options
    w
    Warning:
    Be careful when working inside the printer as some components 
    are sharp and may cause injury.
    1. Turn the printer off and unplug the power cord and all the  interface cables.
    *OFF
    c
    Caution:
    Make sure to unplug the power cord from the printer to 
    prevent getting an electrical shock.
    *
     
    						
    							
    Installing Options297
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    2. Remove the cover on the back of the standard lower cassette.
    3. Loosen the three screws on the back of the printer.
     
    						
    							
    298Installing Options
    4. Pull out the circuit board tray.
    5. Align the three screw holes on the Hard Disk Drive with the 
    screw holes on the circuit board. Secure it by tightening the 
    three screws provided.
     
    						
    							
    Installing Options299
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    Note:
    Be careful not to damage the cable when tightening the screws.
    c
    Caution:
    Do not remove any modules from the circuit board. 
    Otherwise, the printer will not work.
    6. Connect the Hard Disk Drive cable to the circuit board.
     
    						
    							
    300Installing Options
    7. Slide the circuit board tray into the printer.
    8. Fasten the circuit board tray with the three screws.
    9. Reattach the cover.
    10. Reconnect all the interface cables and the power cord.
    11. Plug the printer’s power cord into an electrical outlet.
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C4200DN User Manual