Comdial DIGITECH Digital Telephone System Instructions Manual

SYSTEM CONFIGURATION
Mark the desired selections in the charts to record programming needs.
Dial the feature code and then dial the selection code or press the programming button to program the selection.
IOZE: A current program setting is indicated by a lighted LED next to fhe pmgramming button for fhaf selection.When a fcggfe (on/ofl) acfion
is provided by a sing/e button, the lighted LED indicates an active feature.
eEATURE DESCRIPTION
base Level: The first step in any
rogramming sequence is to enter...

faPress 
ITCM +# # 7 4 6 +k for base level.
FEATURE DESCRIPTION
Recall/Flash: A line disconnect
:recall) or a host system feature
access signal (flash) can be
generated depending upon the
xogrammed time.
Pause Tlme: During auto dials and
speed dials, it is sometimes
necessary to delay the sending of
digits to give switching equipment
time to prepare for receiving them. A
pause is stored whenever the user
presses the 
HOLD button. The pause
length options are stored in seconds.ENTRY CODE AND PROMPTING...

IPress ITCM +k # 7 4 6 t for base level.II1
FEATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAY
‘lmed Hold Recall: 
After a call has
een on hold for a programmed
mgth of time, the system will recall
ie station that placed the call on
old. The timing is in seconds.
Iata Baud Rate: The speed or baud
ate of the data bit stream, which
:arries the SMDR and configuration
lata between the system and an
rxternal data device, must be
jrogrammed to match the
equirements of the data device.VOTE: 
If XMODEM p#tocol...

Press ITCM % # 7 4 6 +# for base level.
FEATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAY
rone or Voice Slgnalllng: Intercom
:alls can be tone signalled or voice
signalled. The first choice in
SignaIling is programmable.
Delete Statlon Message Detall
Accounting (SMDA) records by
Attendant: 
When SMDA records
exceed storage capacity, they must
be deleted 
to make mom for more.
The attendant can be allowed to
delete these records if enabled by this
programming step.
DO Not Disturb (DND) Inhlblt: Any...

-
I
Press ITCM f # 7 4 6 +k for base level.I
:EATUFlE DESCRIPTION
StatIon Monltorlng: The DSS/BLF at
1 station provides idle, busy and line
inging status of monitored stations. If
he flashing BLF lights associated with
risual ring indication are deemed
distracting, this visual indication can
>e disabled system-wide.
Call Park Recall Tlme: A call that is
left in 
a parking orbit for a
programmed length of time
automatically returns to a timed hold
recall condition at the parking station.
Exclusive Hold:...

4
i
Press ITCM +k # 7 4 6 % for base level.
11
FEATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAYREFERENCE RECORD
randem Attendant: When this1. Dial 24.“TANDEM ATTN XXX ”
eature is enabled, a recall from an
2. Press Al to toggle between enable and disable
Jnanswered call transfer or timed hold
(LED On = Enable).
vecall will ring at both attendant-OR-El
stations. When disabled, only the
Dial 1 to enable.“TANDEM ATTN OFF”
attendant station which transferred
:he call will ring.Dial 2 to disable
(Al LED is...

Press ITCM t # 7 4 6 f for base level.I
:eature Inhlblt Programming:
:ertain features can be disabled
ystem-wide to provide a basic
?lephone system for use in
lstallations where a large proportion
If the stations are accessible to
inauthorized users thus subject to
ampering. These features are
nabled when system default is
betformed.
. Dial 29.
. Select feature.“FEATURE INHIBIT”
- Dial 01 to disable Line Group 1.
- Dial 02 to disable Line Group 2.
- Dial 03 to disable Line Group 3.
- Dial 04 to disable...

Press ITCM +k # 7 4 6 +k for base level.
‘A Options: The PA port can beRinging
Issigned lines for direct ring, delayed1. Dial 60.‘P.A. OPTIONS ‘I
ing, or night transfer (of ringing). The
2. Choose ringing assignment.
art can also be arranged to receive
Dial 1 for direct ring.“DIRECT RING ‘.
fither zone or all-call paging.
Dial 2 for delay ring.“DELAY RING ”
Dial 3 for night ring.“NIGHT RING ”telay tracking of the enabled ringing
3. Select line ports:
:an be selected as either station 17
inging or paging...

‘A Options - continuedContinued from previous page
Rlnglng Tracking Relay1. Dial 60.
“P.A. PORT ”2. Dial 5.“RELAY XXXXXXX”
3. Choose relay tracking assignment.
Press Al to toggle between
paging port and station port 17.
(LED On = paging port)
-OR-Dial 1 for station port 17. “RELAY STA. 17
”Dial 2 for paging port.“RELAY P.A. PORT”
4. Dial 
+k for next PA option.
-OR-
Dial 
% t for configuration mode.
Press ITCM +K # 7 4 6 * for base level.
FEATURE DESCRIPTION
Extended DTMF Tones For
Automatic Dlallng:...

f
0
LINE CONFIGURATION1
 Mark the desired selections in the charts to record programming needs.1
 Dial the feature code and then dial the selection code or press the programming button to program the selection.
JOTE: A current program setting is indicated b
cra lighted LED next to the programming button for that selection.When a toggle (on/off) action is
provided 
by a &g/e button, the lighteLED indicates an active feature.1
 To make a line port selection, press a programming button or dial a selection...