Home
>
Comdial
>
Communications System
>
Comdial DIGITECH Digital Telephone System Instructions Manual
Comdial DIGITECH Digital Telephone System Instructions Manual
Here you can view all the pages of manual Comdial DIGITECH Digital Telephone System Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 21
be effected. If the other station does not have access to the incoming line, transfer can still take place using the system transfer feature. For a screened transfer, a call is transferred to another station with a pre-transfer announcement by the transferring patty. Transferring calls is accomplished with the TRANSCONF button. Also refer to the discussion titled: Call Transfer- Unscreened. CALL TRANSFER - UNSCREENED, An active call can be transferred to another station without being announced. The...
Page 22
8. __, ,,.rtion Of System FeatureslMl66-083CONFERENCING - ADD-ON With this feature, a station, operating in a private mode, can add up to four other stations to an outside call.CONFERENCING - MULTILINE This feature will allow one station to access up to four outside lines at the same time resulting in a conference arrangement. Conferencing is established through the use of the TRANSKONF button., CONFERENCING - UNSUPERVISED After a conference between an internal party and a maximum of two external...
Page 23
lMl66-083Description Of System Feat. Other Calls: This is a summation of the time spent on outgoing call activity, incoming call activity on non-department lines, plus all intercom call activity. On-Duty Time: The on-duty time includes a summation of idle time, department call time, wrap-up time, and other call time. Off-Duty Time: The time that a station spent in a do not disturb mode. While in a do-notdisturb condition, a station is not available tc receive calls. The station user sets a...
Page 24
,&Ion Of System FeatureslMl66-083 Further, the system camp-on feature cannot be used to camp-on to a department. Subsequent calls to a department on a particular line always try the next station in the department from whichever station serviced the last call on that line. This means that if department stations 15 and 16 are programmed to answer line 1, and station 15 services a call, the next line 1 call will ring at station 16. When both stations 15 and 16 are programmed to answer lines 1, 2 and 3,...
Page 25
lM166-083Description Of System Feats to the DISD assist station if one is programmed; otherwise, the line is dropped. If the assist station is busy (call will camp-on at the assist station) or lf the assist station does not answer before the transfer recall timeout period, the system will return the caller to DISD dial tone. If extension number dialing is not completed within the dial time limit this time, the line is dropped. It is recommended that a music source be connected to the system to provide...
Page 26
..tron Of System FeatureslMl66-083 line class of service programming arranges a line port for external paging interface. operations can be performed. Station class of service programming allows certain buttons to be programmed as dynamic line buttons FEATURE INHIBIT END-TO-END SIGNALLINGON INTERCOM After an intercom call has been established, the system can continue to send dialing signals (DTMF tones) through the intercom path. This feature can be performed from every station in the system, and iss...
Page 27
re-locating the station and line wiring. Line and station class of service programming are used to reassign stations and lines. Also refer to the discussion titled, Auxiliary Ringer Interface. FLEXIBLE STATION NUMBERING PLAN The system supports a flexible station numbering plan for individual stations. Each station can be programmed to respond to the dialing of any available number between 10 and 7999. This feature may be used to match the calling number of a station located in a pre-numbered area to...
Page 28
always automatically replace a previously dialed number. Upon command, the system will choose a Line and redial the saved number. The system will first choose the prime line if assigned and idle. If it is busy or unavailable, the system will choose any line assigned to idle line preference. If they are unavailable, the system will chose the last line used at the station. If it is busy, no further choice is made. No class of service is required. Also refer to thediscussion titled: Automatic Pause...
Page 29
lMl66-083Description Of System Feat,.‘. programming provides a station with the ability to originate a message waiting signal and is used to create a central message desk.MODULAR WIRING AND JACKSR- OR 4-CONDUCTOR WIRE SYSTEM The system can be completely interconnected by employing industry standard 50-pin connectors and modular plug/jack combinations. Station wiring is small, 2conductor, twisted-pair cable throughout the system. A 4conductor twisted-pair cable can be employed if a spare pair is...
Page 30
.,,tron Of System FeatureslMl66-083 off hook. Prime line pickup may be pre-empted by preselecting another line before lifting the handset. lf the prime line is ringing, lt is automatically answered by lifting the handset. Prime line automatic is assigned t0 a station through station class of service programming. PRIVACY - DESIGNATEDPROGRAMMABLE BUlTON Stations can be programmed to provide a privacy button. If a line is private, a user can press the privacy button to change it into a non-private one....